Ormazabal velatia ekor.bat-200 General Instructions Manual Download Page 12

IG-258-EN, version 02; 16/11/2018

12

Connections 

General Instructions

ekor

.bat-200

4.2.  LED indications

The charger has eight light indicators. Some of these can 
show double signalling. The indications only use a flashing 
frequency.

LED

Text 

Mode 

Associated function

Green

Power ON

On

Charger running on battery or network

Green

Battery charging

Flashing 

Charge mode: Fast. (Constant voltage)

On

Charge mode: Floating

Green

Battery test

On

Working battery test

Yellow

Battery discharging

On

Battery discharging

Red

V

AC

 IN ERROR

Flashing 

Network input outside of permitted margins

Red

V

DC

 OUT ERROR

Flashing 

24/48 V

dc

 output outside of permitted margins

Red

Battery ERROR

Flashing 

 Absence of battery, battery disconnected

On

Battery test failure, end of battery's working life

Red

Charger ERROR

Flashing 

Anomalies in charger. Temperature sensor, others…

On

Temperature sensor failure

Table 4.2. 

Description of the indications by LED

4.3.  Alarms

Name

Logic

Input network failure

The contact is open in normal operation.
It closes if AC voltage input is out of range, or there is an absence of AC voltage.

Urgent charger-rectifier failure  

The contact is open in normal operation.
It closes if:
•  There is no battery connected.
•  Battery Test Failure.
•  Urgent internal failures.
•  Charger temperature out of range.

Non-urgent charger-rectifier failure 

The contact is open in normal operation.
It closes if:
•  Max battery voltage
•  Temperature sensor error
•  Output voltage out of range.
•  Battery temperature out  range.

End of battery life

The contact is open in normal operation.
It closes if battery voltage drops below minimum discharge voltage.

Table 4.3. 

Alarms

Summary of Contents for velatia ekor.bat-200





















Reviews: