background image

4

STAND UNIT

5

Infinitely Expandable 

S

TAND UNIT

Safety Precaution

1. 

※Please.keep.all.the.cautions.and.warnings.for.proper.use.of.the.product.and.prevent.possible.accident.or.hazard.
※You.can.find.“CAUTION”.and.“WARNING”.signs.in.this.manual..Each.sign.has.following.meaning.

Please read and understand this manual fully before installation.

 

¹

Please hand over this manual to customers after installation and ask to read 

 

¹

and keep this manual for future use.

WARNING

   If the user does not comply with this instruction, serious injuries or death 

can be caused.

CAUTION

   If the user does not comply with this instruction, minor injuries or product 

damage can be caused.

Installation must be done by the skilled persons 

designated by sales agent or dealership.

Installation work can be very dangerous for inexperienced 
person.
It may cause serious injury or even death.

Do not install at unstable locations that cannot 

withstand product weight. 

In case of weak floor or ground, product may fall and cause 

injuries.

If you need to move or replace the product, 

please contact with skilled persons designated 

by sales agent or dealership

If users move or install the product without proper skill and 

experience, it may cause safety problem. 

Do not hang on the product and avoid severe 

impact to the product.

Product may fall and cause injuries.

WARNING

Please install as described in this manual.

Improper installation may cause serious injury or product 
damage.

Installation of this product needs 3 or more 

people.

3 or more people need to work together to avoid personal injury 
or product damage. 

Use enclosed accessories. 

Improper accessories may not withstand the weight of the 
product.  It may cause safety problems.

Install on the even ground or floor.

Product installed on uneven places such as inclined places or 
stairways may fall and cause personal injury or product damage.

Do not use heaters or humidifiers at the place of 

installation.

Heat or vapor may cause fire, electric shock or malfunction.

Do not install the product near to sprinkler, fire 

detector, high-voltage cable, power source, or 

places of vibration or impact.

Make sure to disconnect before installation.

If you install the product while the power cord is still connected, 
it may cause electric shock or fire.

Use working gloves when you install.

Wear working gloves to avoid any injury. 

CAUTION

User's Manual

Summary of Contents for MPDP

























Reviews: