Orion MPDP User Manual Download Page 13

Page: 13 / 24

WALL UNIT

Infinitely Expandable

ALL UNIT

Safety Precaution

※.Please.keep.all.the.cautions.and.warnings.for.proper.use.of.the.product.and.prevent.possible.accident.or.hazard.
※.You.can.find."CAUTION".and."WARNING".signs.in.this.manual..Each.sign.has.following.meaning.

Please read and understand this manual fully before installation.

Please handover this manual to customers after installation and ask to read

and keep this manual for future use.

WARNING

If the user does not comply with this instruction, serious injuries or death

can be caused.

CAUTION

If the user does not comply with this instruction, minor injuries or product

damage can be caused.

WARNING

Installation must be done by the skilled persons

designated by sales agent or dealership.

Installation work can be very dangerous for inexperienced
person.
It may cause serious injury or even death.

Avoid weak or unstable locations.

MPDP sets may fall, if the location of installation cannot

withstand the weight of MPDP sets.
It may cause personal injury or product damage.

When you need to move or replace the

product after installation, contact with the

skilled persons designated by sales agent or

dealership.

Installation work can be very dangerous for inexperienced
person.
It may cause safety problems.

CAUTION

Please install as described in this manual.

Improper installation may cause serious injury or product
damage.

Installation of this product needs 6 or more

skilled people.

6 or more people need to work together to avoid personal injury
or product damage.

Check the condition and type of wall before

installation. If all the condition fits, use enclosed

anchors and bolts.

Unauthorized anchors and bolts may not withstand the weight of
the product and may cause safety problems.

Make sure to use the drill and bit of specified

diameter. Follow the instruction for the depth of

the hole, too.

Unspecified way of drilling may cause unstable installation. It

may cause safety problems.

Do not use heaters or humidifiers at the place of

installation.

Heat or vapor may cause fire, electric shock or malfunction.

Do not install the product near to sprinkler, fire

detector, high-voltage cable, power source, or

places of vibration or impact.

Make sure to disconnect power cord before

installation.

If you install the product while the power cord is still connected,
it may cause electric shock or fire.

Use working gloves when you install.

Wear working gloves to avoid any injury.

User's Manual

Do not hang on the product or give any impact.

Product may fall and cause person injury.

Summary of Contents for MPDP

























Search results

Summary of Contents for MPDP

Reviews:

Related manuals for MPDP

Brands by name

Popular brands

Orion MPDP, User Manual

Search results

Summary of Contents for MPDP

Reviews:

Related manuals for MPDP

Brands by name

Popular brands