manualshive.com logo in svg

Oracle X8-8, Installation Manual

Share
Download
Oracle X8-8 Installation Manual Download Page 57

Connecting Cables and Applying Power

This section contains procedures for connecting data management and server management

cables and power cords to the server. The server initial power-on procedure is also described.

■

“Cabling Requirements” on page 57

■

“Back Panel Connectors and Ports” on page 58

■

“Server Management Connection Options” on page 63

■

“Connect Cables and Power Cords” on page 64

■

“Power On the Server” on page 66

Related Information

■

“Installation Procedure Overview” on page 11

■

“Using Oracle Integrated Lights Out Manager (ILOM)” on page 73

Cabling Requirements

Read the following cable requirements for connecting the server.

■

Minimum cable connections for the server:

■

At least one server on-board Ethernet network connection (NET port)
See 

“Ethernet Ports” on page 62

.

■

Serial management port (SER MGT): Service processor (SP) local connection for

Oracle ILOM boot messages
See 

“SER MGT Ports” on page 60

.

■

Power cables for the server power supplies
See 

“Connect Cables and Power Cords” on page 64

.

■

SP management ports:

 There are two service processor management ports.

Connecting Cables and Applying Power

57

Summary of Contents for X8-8







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands