background image

To Connect the HBA to Internal Storage Devices

9

Edge of host board

Note - 

The host adapter shape, size, and locations of components may vary from this

illustration.

4.

When the HBA is fully inserted in the slot, secure the HBA to the chassis of the

system by installing the bracket screw, if applicable, or by engaging the system

retention mechanism.

To Connect the HBA to Internal Storage Devices

1.

Configure and install the SAS devices, SATA devices, or both in the system.

For more information, see the documentation for the storage devices.

2.

Connect the serial SAS cables to the two internal x4 mini-SAS connectors and

attach the other end of the cables to the serial disk drives or other SAS/SATA

devices, per your requirements (

Figure 2, “Installing the HBA,” on page 19

).

Use only Oracle-provided SAS cables (provided with your system at time of purchase). You can

also purchase Oracle cables at 

http://www.oracle.com

.

3.

Observe the light-emitting diodes (LEDs) during data transfer on the connected

drives to ensure normal operation of the HBA.

To Complete the Installation

1.

Replace the system cover and reconnect the AC power cords, as described in

the system documentation.

2.

If you needed to turn the system power off as part of the installation, turn power

on to the system.

Note - 

Ensure that the power is turned on to the SAS devices, SATA II devices, or both before

or at the same time that the power is turned on to the host system. If the system is powered up

before these devices, the devices might not be recognized.

20

Sun Storage 6 Gb SAS PCIe HBA, Internal Installation Guide For HBA Models SGX-SAS6-INT-Z and SG-SAS6-INT-Z

• May 2017

Summary of Contents for SG-SAS6-INT-Z

















































































Reviews: