background image

Installing the Oracle Solaris OS

4.

Type 

q

 to exit the utility.

FORMAT MENU:
  disk  - select a disk
  type  - select (define) a disk type
  partition  - select (define) a partition table
  current  - describe the current disk
  format  - format and analyze the disk
  fdisk  - run the fdisk program
  repair  - repair a defective sector
  label  - write label to the disk
  analyze  - surface analysis
  defect  - defect list management
  backup  - search for backup labels
  verify  - read and display labels
  save  - save new disk/partition definitions
  inquiry  - show vendor, product and revision
  scsi  - independent SCSI mode selects
  cache  - enable, disable or query SCSI disk cache
  volname  - set 8-character volume name
  !<cmd>  - execute <cmd>, then return
  quit
format> 

q

Next Steps

If you are installing the HBA in a SPARC system, install the Oracle Solaris OS, as described in

“Installing the Oracle Solaris OS” on page 51

.

If you are installing the HBA in an x86 system, install a supported OS (for a list of supported

OSes, see 

“Operating System and Technology Requirements” on page 13

. If you plan to install

the Oracle Solaris OS on an x86 system, follow the instructions in 

“Installing the Oracle Solaris

OS” on page 51

.

Installing the Oracle Solaris OS

You can install the Oracle Solaris 10 01/13 OS, at minimum, on the bootable drive that

you created, as described in this chapter. Starting with the Oracle Solaris 10 01/13 OS, the

driver required by the HBA is provided with the Oracle Solaris OS. This section contains the

following topics:

Chapter 3 • Creating a Bootable Drive in a Preboot Environment

51

Summary of Contents for SG-SAS6-INT-Z

















































































Reviews: