Oracle ALEXANDRIA MK III Owner'S Manual Download

Page: 16 / 17

WHAT DO TO IF….

IF THE TURNTABLE DOES NOT START AND THE SPEED INDICATING LIGHT DOES NOT GO ON.

Check AC connection to the wall outlet

Power supply output plug to the input receptacle of the turntable

Power supply output , if no output, replace the fuse inside.

IF THE TURNTABLE DOES NOT START AND THE SPEED INDICATING LIGHT GOES ON

Check the drive belt

Motor connection plug for a broken wire

Drive module for a broken wire

Defective drive module

IF THE PLATTER IS NOT PARALLEL WITH THE PLINTH

Check the suspension calibration using the suspension gauge

Note: if a relatively important change occurred in one particular suspension module, this

could be the sign of an improperly seated spring or sorbothane ring, analyze each part

carefully prior to calibrating the supsenion

Read: section How to….assess the suspension calibration

Read: section How to….calibrate the suspension

IF AN EVEN UP OR DOWN MOTION CANNOT BE OBTAINED WHEN GENTLY PRESSING ON THE

RECORD CLAMP.

Check leveling of the base

For the phono lead interference with the movement of the suspension. If uncertain, unplug

the lead.

Previous topic: …do if the platter is not parallel with the plinth.

ALEXANDRIA MK III

Owner’s manual

Summary of Contents for ALEXANDRIA MK III


















Search results

Summary of Contents for ALEXANDRIA MK III

Reviews:

Related manuals for ALEXANDRIA MK III

Brands by name

Popular brands

Oracle ALEXANDRIA MK III, Owner'S Manual

Search results

Summary of Contents for ALEXANDRIA MK III

Reviews:

Related manuals for ALEXANDRIA MK III

Brands by name

Popular brands