manualshive.com logo in svg

Oracle ALEXANDRIA MK III, Owner'S Manual, Page: 14 / 17

Share
Download
Oracle ALEXANDRIA MK III Owner'S Manual Download Page 14

 

Install the belt 

 

 

Note 1: To reduce contamination problems, wash your hands prior to handling the drive belt. 

 

-

 

With the platter upside down, place the belt around the hub. 

 

-

 

Bring the platter over the bearing and lower it straight down holding the belt stretched 

beyond the machined groove in the platter. 

 

-

 

Guide the drive belt around the motor pulley when the spindle first stop over the oil in the 

bearing. 

 

Note 2: Do not attempt to rotate the platter at this time since it is not yet fully seated against 

thrust pad. The spindle will first rest over the oil creating an hydraulic lock and the weight of the 

platter will gradually allow if to seat against the thrust pad. This whole process should be 

completed withtin one minute. 

 

Note 3: In the event that the drive belt becomes contaminated, clean it with denatured alcohol. 

Clean the motor pulley and the drive hub at the same time. 

 

 

Remove the platter with the drive belt installed 

 

 

-Place one hand at the rear over the motor, one hand at the front, lift the platter about 

25cm ( one inch ) and with one finger pull the belt off the motor pulley, then lift the platter 

straight up. 

 

Install the dust cover 

 

 

Note:The hinges are already mounted to the dust cover. 

 

-

 

Slide the hinge flap in the anchor plates at the rear of your Alexandria. 

 

 

Connect the power supply 

 

-

 

Plug the supply output to the turntable input receptacle at the rear of the turntable. 

 

-

 

Plug the input cord to an AC outlet. 

 

Note: Keep the power supply away from the signal carrying leads 

 

 

 

 

 

 

 

 

 

 

 

 

ALEXANDRIA MK III 

Owner’s manual 

 

 

Summary of Contents for ALEXANDRIA MK III


















Reviews:

No comments