OPTO-EDU A15 0908 Series Instructions Manual Download Page 2

Page: 2 / 24

Contents

A15.0908 Series

Before Use

1. Components

............................................................................................................................... 1

2. Assembling

................................................................................................................................ 3

2-1

Assembling Scheme

......................................................................................................... 3

2-2

Assembling Steps

............................................................................................................. 4

3. Operation

.................................................................................................................................. 8

3-1

Set Illuminations

............................................................................................................. 8

3-2

Adjust Focusing

.............................................................................................................. 9

3-3

Adjust the Focusing Tension

........................................................................................... 9

3-4

Adjust the Diopter

........................................................................................................... 9

3-5

Adjust the Interpupillary Distance

................................................................................ 10

3-6

Use the Eye-cap

............................................................................................................ 10

3-7

Adjust the Objective Center

.......................................................................................... 10

3-8

Center the Condenser

....................................................................................................11

3-9

Adjust the Field Diaphragm

.......................................................................................... 12

3-10

Adjust the Aperture Diaphragm

.................................................................................. 12

3-11

Adjust the Analyzer

..................................................................................................... 13

3-12

Adjust the Polarizer

.................................................................................................... 13

3-13

Check H-V Location

.................................................................................................... 14

3-14

Use the Compensator

.................................................................................................. 14

3-15

Use the Rotatable Stage

.............................................................................................. 14

3-16

Use the Color Filter

.................................................................................................... 14

3-17

Replace the Fuse

......................................................................................................... 15

3-18

Use the Bertrand Lens

................................................................................................ 15

3-19

Use the Trinocular Head, TV and Photography Device

.............................................. 16

3-20

Use the Digital Viewing Head

..................................................................................... 17

4. Troubleshooting

....................................................................................................................... 19

Summary of Contents for A15 0908 Series

























Search results

Summary of Contents for A15 0908 Series

Reviews:

Related manuals for A15 0908 Series

Brands by name

Popular brands

OPTO-EDU A15 0908 Series, Instructions Manual

Search results

Summary of Contents for A15 0908 Series

Reviews:

Related manuals for A15 0908 Series

Brands by name

Popular brands