Opticon OPR 3001 Specification Manual Download Page 35

Page: 35 / 42

Opticon

OPR 3001

Specifications Manual

13. Durability

13.1. Electrical Noise

No malfunction occurred when sinusoidal electrical noise (10 Hz–100 kHz, < 0.1 Vp-p)
was added to the power supply line.

Conditions

Barcode Sample: OPTOELECTRONICS Test Sample

PCS 0.9

Resolution 0.25

Symbology

9-digit Code 39

Quiet Zone

10 mm

N/W Ratio

1:2.5

Distance 100

Angle

= 0°

= 15°

= 0°

Curvature R

∞

Power Supply Voltage

6.0 V (RS-232C) / 5.0 V
(USB and Wedge)

13.2. Static Electricity

Air discharge:

8 kV max (No malfunction)
15 kV max (No destruction)

Contact discharge:

6 kV
Contact discharge at the hook and the screw

Measurement environment:

Use electrostatic testing device compliant with IEC 61000-4-2

Discharge resistance:

330

Ω

Capacitor charging:

150 pF

Summary of Contents for OPR 3001











































Search results

Summary of Contents for OPR 3001

Reviews:

Related manuals for OPR 3001

Brands by name

Popular brands

Opticon OPR 3001, Specification Manual

Search results

Summary of Contents for OPR 3001

Reviews:

Related manuals for OPR 3001

Brands by name

Popular brands