Opticon OPR 3001 Specification Manual Download Page 24 | Manualshive

Page: 24 / 42

background image

Opticon

OPR 3001

Specifications Manual

24

8.2. USB-HID and USB-VCP Interface Specifications

8.2.1.

Settings

Reading the menu barcodes in section 10.1 can set the USB interface default.
The interface is full-speed USB (12 Mbps).

8.2.2.

Interface Circuit

Figure 18: USB interface circuit

Do not operate the keyboard while the scanner is transmitting the data to the host;
it may cause data transactions to fail.

8.3. DOS/V Wedge Interface Specification

Reading the menu barcodes in section 10.1 can set the DOS/V Wedge interface default.

Do not operate the keyboard while the scanner is transmitting the data to the host; it may
cause data transactions to fail.

«
...
22
23
24
25
26
...
»

Summary of Contents for OPR 3001











































Reviews:

No comments

Related manuals for OPR 3001

Brand: Tolino Pages: 79

Brand: Slick Pages: 41

Brand: C Prox Pages: 7

Brand: Kathrein Pages: 12

MOVIEVIEWS FLX-110

Brand: Franklin Pages: 22

KAAN Standard Plus

Brand: Kobil Pages: 73

Tiris 2000 Series

Brand: Texas Instruments Pages: 46

Brand: Sebury Pages: 3

Brand: Microscan Pages: 132

Brand: Access Interfacing Solutions Pages: 70

Brand: Datalogic Pages: 49

GA-2408T Series

Brand: Gainscha Pages: 93

M3 ORANGE Snap-On

Brand: M3 Mobile Pages: 17

Pocketbook 360 Plus

Brand: Obreey Pages: 67

Brand: zenpert Pages: 34

SD All in One Card Reader

Brand: Hama Pages: 22

Brand: Youjie Pages: 16

Brand: Quick-Ohm Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands