Detectable Speed
Power Input
This unit is designed to detect movement of an intruder and activate an alarm control panel. Being only a part of a complete system, we cannot accept
responsibility for any damages or other consequences resulting from an intrusion. This product confirms to the EMC Directive 89/336 EEC.
PROBLEM
PROBABLE CAUSE
REMEDY
Incorrect power supply voltage.
Faulty wiring to detector. Transmitter is not
connected to BX-80NR
Wireless transmission does not reach the receiver.
Battery is dead.
Normal Performance. Refer to section "8-2.2.
BATTERY SAVING TIMER" and "8-2.1.WALK TEST MODE".
No alarm event even though
someone is walking in
detection area.
LED blinks continuously
Make alarms even though no
moving object is in the area
No detection occasionally
Incorrect power supply voltage.
Detector is not installed perpendicular to the ground.
Lower detection area is unnecessarily long.
Lower detection area any object.
Lower detection area is exposed to direct sunlight or
car light.
There is a heat source (stove or heater, etc.) in the
area that may cause temperature change.
There is a moving object (laundrt on clothesline,
plants, etc.) in the area.
Detection area is not set appropriately.
Sensitivity is set for L(ow)
Set supply voltage for a range of 3 to 9VDC battery.
Rewire alarm correcty.
Check transmitter.
Change battery.
Battery saving timer is working.
Reinstall the detector perpendicular to the ground.
Confirm and reset the detection area.
Remove the reflector or reset the detection area
reflected light.
Reset the area so it does not receive direct light.
Reset the area or remove the heat source.
Reset the area or remove moving objects.
Reset the area appropriately.
Reset sensitivity for M(edium) or H(igh).
mm(inch)
33(1.30)
9(0.36)
1
5
(0
.5
9
)
Magnetic Contact
MODEL
BX-80NR
Detection Method
Passive Infrared
Coverage
24m (80ft.) (12m(40ft.) on each side)
Detection Zones
4 zone (2 zone on each side)
Sensitivity
2°C at 0.6m/s (3°F at 2.0ft/s)
0.3-1.5m/s (1-5ft/s)
2.5-10VDC
Current Draw
3mA (Walktest, LED on) 15uA (Standby)
Alarm Period
2.0±1.0 sec.
Relay Output
Tamper Switch
Form C changes when cover removed
Walk Test Mode
ON / OFF
Warm-up Period
Approx. 2 min.
LED Indicator
RF Interference
No Alarm 20 V/m
Mounting
Wall (Indoor/Outdoor)
Mounting Height
Weight
520g (18.4oz)
IP rating
IP55
Accessories
MOUNT SCREW (+4×20) × 2, BATTERY LEAD× 2
Form C-Solid state switch : 10VDC, 0.01A(MAX.)
Disable during normal operation
Enable during WALK TEST or LED SW on
-20°C
㨪
+50°C(-4°F
㨪
+122°F)
Environmental Humidity
95%(MAX.)
0.8
㨪
1.2m (2.7
㨪
4ft.)
ALARM CABLE, 006P CONNECTER CABLE,
Operating Temperature
No detection occasionally
when conduct walk tests.
Walk test switch is OFF.
(Battery saving timer is working.)
Switch ON the walk test mode. Refer to section
"8-2.1.WALK TEST MODE".
̪
Specifications and design are subject to change without prior notice.
SPONGE PAD,VELCRO TAPE× 2
5
6
(2
.2
0
)
128(5.04)
60(2.36)
M
o
u
n
ti
n
g
P
it
c
h
8
3
.5
(3
.2
8
)
2
3
5
(9
.2
5
)
OPTEX CO., LTD.
(JAPAN)
(ISO9001 Certified by LRQA)
(ISO14001 Certified by JET)
5-8-12 Ogoto
Otsu, Shiga 520-0101
Japan
Tel:+81-77-579-8670
Fax:+81-77-579-8190
http://www.optex.co.jp/e
OPTEX INCORPORATED
(USA)
13661 Benson Ave., Bldg.C.Chino,
CA 91710 U.S.A.
Tel:+1-909-993-5770
Fax:+1-909-628-5560
http://www.optexamerica.com
OPTEX (EUROPE) LTD.
(UK)
(ISO 9001 Certified by NQA)
Clivemont Road, Maidenhead,
Berkshire, SL6 7BU
UK
Tel:+44-1628-631000
Fax:+44-1628-636311
http://www.optexeurope.com
OPTEX SECURITY SAS
(FRANCE)
Batiment Sis 475, Rue Piani 69480
Amberieux d'Azergues, France
Tel:+33-437-55-50-50
Fax:+33-437-55-50-59
http://www.optex-security.com
OPTEX KOREA CO., LTD.
(KOREA)
1001 Sambu Renaissance-Tower 456,
Kongduck-Dong, Mapo-Gu, Seoul
Korea
Tel:+82-2-719-5971
Fax:+82-2-719-5973
http://www.optexkorea.com
OPTEX SECURITY SP.Z O.O.
(POLAND)
ul. Bitwy Warszawskiej 1920 r. 7B,02-366
Warszawa, Poland
Tel:+48-22-598-06-60
Fax:+48-22-598-06-61
10. SPECIFICATIONS & DIMENSIONS
11. TROUBLE SHOOTING
3-9VDC Lithium or Alkaline Battery
Operating Voltage
Set supply voltage for a range of 3 to 9 VDC battery.
5913801 06.11.11
Summary of Contents for Boundary Gard BX-80NR
Page 2: ......
