50
4. Press ENTER with "Update" selected to start update.
0
During the update, the TV screen may go black
depending on the updated program. In that case,
check the progress on the display of the unit. The TV
screen will remain black until the update is complete
and the power is turned on again.
0
"Completed!" is displayed when the update is
complete.
5. Press
Í
ON/STANDBY on the main unit to switch the
unit to standby. The process is completed and your
firmware is updated to the latest version.
0
Do not use
Í
on the remote controller.
If an Error Message is Displayed:
When an error occurs,
"
¢
-
¢¢
Error!" is displayed on the display of the unit. ("
¢
"
represents an alphanumeric character.) Check the
following:
0
¢
-01,
¢
-10:
Cannot recognize Ethernet cable. Connect
the Ethernet cable properly.
0
¢
-02,
¢
-03,
¢
-04,
¢
-05,
¢
-06,
¢
-11,
¢
-13,
¢
-14,
¢
-16,
¢
-17,
¢
-18,
¢
-20,
¢
-21:
Internet connection error.
Check the following:
– Whether the router is turned on
– Whether this unit and router are connected to the
network
Try to disconnect and then connect again the power to
the unit and router. This may solve the problem. If you
are still unable to connect to the Internet, the DNS server
or proxy server may be temporarily down. Check the
service status with your ISP provider.
0
Others
: Disconnect then reconnect the power cord, then
repeat from the beginning.
Updating via USB
0
Prepare a 128MB or larger USB storage device. FAT16
or FAT32 file system format.
– Media inserted in a USB card reader may not be used
for this function.
– USB storage devices with security function are not
supported.
– USB hubs and USB devices with hub function are not
supported. Do not connect these devices to the unit.
0
Delete any data stored on the USB storage device.
0
Turn off the controller component (PC etc.) connected to
the network.
0
Stop any playing Internet radio, USB storage device, or
server content.
0
If the multi-zone function is active, turn it off.
0
When "5. Hardware" - "HDMI" - "HDMI CEC" is set to
"On" in the Setup menu, set to "Off".
0
Some USB storage devices may take long to load, may
not be loaded correctly, or may not be correctly fed
depending on the device or their content.
0
We will not be liable whatsoever for any loss or damage
of data, or storage failure arising from the use of the USB
storage device with this AV receiver. Thank you for your
understanding.
0
The description may differ from the on-screen display but
that will not change the way to operate or the function.
1. Connect the USB storage device to your PC.
2. Download the firmware file from the our website to your
PC and unzip.
Firmware files are named in the following way:
ONKAVR
¢¢¢¢
_
¢¢¢¢¢¢¢¢¢¢¢¢
.zip
Unzip the file on your PC. The number of unzipped files
and folders varies depending on the model.
3. Copy all unzipped files and folders to the root folder of
the USB storage device.
0
Make sure to copy the unzipped files.
4. Connect the USB storage device to the USB port on the
main unit.
0
If you connect a USB hard disk drive to the USB port
of the unit, we recommend that you use its AC adapter
to power it.
0
If the USB storage device has been partitioned, each
section will be treated as an independent device.
5. Switch the input on the TV to that assigned to the unit.
6. Press SETUP on the remote controller.
7. Select "7. Miscellaneous" - "Firmware Update" -"Update
via USB" with the cursors in order and press ENTER.
0
If "Firmware Update" is grayed out and cannot be
selected, wait for a while until it starts up.
0
You will not be able to select "Update via USB" if there
is no firmware update.
8. Press ENTER with "Update" selected to start update.
0
During the update, the TV screen may go black
depending on the updated program. In that case,
check the progress on the display of the unit. The TV
screen will remain black until the update is complete
and the power is turned on again.
0
During the update, do not turn off, or disconnect then
reconnect the USB storage device.
0
"Completed!" is displayed when the update is
complete.
9. Disconnect the USB storage device from the main unit.
10.Press
Í
ON/STANDBY on the main unit to switch the
unit to standby. The process is completed and your
firmware is updated to the latest version.
> Install
> Playback
| Supplementary Information | Others
Setup
1. Input/Output Assign
2. Speaker
3. Audio Adjust
4. Source
5. Hardware
6. Multi Zone
7. Miscellaneous
1. TV Out / OSD
2. HDMI Input
3. Digital Audio Input
4. Analog Audio Input
Setup
1. Tuner
2. Firmware Update
3. Initial Setup
4. Lock
1. Input/Output Assign
2. Speaker
3. Audio Adjust
4. Source
5. Hardware
6. Multi Zone
7. Miscellaneous
