background image

©

 Semiconductor Components Industries, LLC, 2016

March, 2016 − Rev. 5

1

Publication Order Number:

KAC−12040/D

KAC-12040

4000 (H) x 3000 (V) 

CMOS Image Sensor

Description

The KAC−12040 Image Sensor is a high-speed 12 megapixel

CMOS image sensor in a 4/3

 optical format based on a 4.7

m

m 5T

CMOS platform. The image sensor features very fast frame rate,
excellent NIR sensitivity, and flexible readout modes with multiple
regions of interest (ROI). The readout architecture enables use of 8, 4,
or 2 LVDS output banks for full resolution readout of 70 frames per
second.

Each LVDS output bank consists of up to 8 differential pairs

operating at 160 MHz DDR for a 320 Mbps data rate per pair.
The pixel architecture allows rolling shutter operation for motion
capture with optimized dynamic range or global shutter for precise
still image capture.

Table 1. GENERAL SPECIFICATIONS

Parameter

Typical Value

Architecture

5T Global Shutter CMOS

Resolution

12 Megapixels

Aspect Ratio

4:3

Pixel Size

4.7

m

m (H) 

×

 4.7

m

m (V)

Total Number of Pixels

4224 (H) 

×

 3192 (V)

Number of Effective Pixels

4016 (H) 

×

 3016 (V)

Number of Active Pixels

4000 (H) 

×

 3000 (V)

Active Image Size

18.8 mm (H) 

×

 14.1 mm (V)

23.5 mm (Diagonal), 4/3

 Optical Format

Master Clock Input Speed

5 MHz to 50 MHZ

Maximum Pixel Clock Speed

160 MHz DDR LVDS, 320 Mbps

Number of LVDS Outputs

64 Differential Pairs

Number of Output Banks

8, 4, or 2

Frame Rate, 12 Mp

1−70 fps 10 bits
1−75 fps 8 bits

Charge Capacity

16,000 electrons

Quantum Efficiency

KAC−12040−CBA
KAC−12040−ABA

40%, 47%, 45% (470, 540, 620 nm)
53%, 15%, 10% (500, 850, 900 nm)

Read Noise
(at Maximum LVDS Clock)

3.7 e

 rms, Rolling Shutter

25.5 e

 rms, Global Shutter

Dynamic Range

73 dB, Rolling Shutter
56 dB, Global Shutter

Blooming Suppression

> 10,000x

Image Lag

1.3 electron

Digital Core Supply

2.0 V

Analog Core Supply

1.8 V

Pixel Supply

2.8 V & 3.5 V

Power Consumption

1.5 W for 12 Mp @ 70 fps 10 bits

Package

267 Pin Ceramic Micro-PGA

Cover Glass

AR Coated, 2-sides

NOTE: All Parameters are specified at T = 40

°

C unless otherwise noted.

www.onsemi.com

Figure 1. KAC−12040 CMOS Image Sensor

Features

Global Shutter and Rolling Shutter

Very Fast Frame Rate

High NIR Sensitivity

Multiple Regions of Interest

Interspersed Video Streams

Applications

Machine Vision

Intelligent Transportation Systems

Surveillance

See detailed ordering and shipping information on page 2 of
this data sheet.

ORDERING INFORMATION

Summary of Contents for KAC-12040











































Reviews: