background image

xvii

Disclaimers

CHANGE IN SPECIFICATIONS 

Product specifications and accessories may be changed at any time based on improvements and other 
reasons.

It is our practice to change model numbers when published ratings or features are changed, or when 
significant construction changes are made. However, some specifications of the products may be changed 
without any notice. When in doubt, special model numbers may be assigned to fix or establish key 
specifications for your application on your request. Please consult with your OMRON representative at any 
time to confirm actual specifications of purchased products.

DIMENSIONS AND WEIGHTS 

Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when 
tolerances are shown.

PERFORMANCE DATA 

Performance data given in this manual is provided as a guide for the user in determining suitability and does 
not constitute a warranty. It may represent the result of OMRON's test conditions, and the users must 
correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty and 
Limitations of Liability.

ERRORS AND OMISSIONS 

The information in this manual has been carefully checked and is believed to be accurate; however, no 
responsibility is assumed for clerical, typographical, or proofreading errors, or omissions.

Summary of Contents for SYSMAC One NSJ Series



























Reviews: