Omron S8BA LF Series Manual Download Page 17

S8BA-LF

17

Stationary installation

Battery Replacement

The UPS supports hot swapping. Battery replacement is possible 
both when the power is turned OFF (while the power output is OFF) 
and when the power is turned ON (while the power output is ON).

For battery replacement, hold down the “Buzzer Pause/Test” 
switch on the unit for 10 seconds or longer to activate the battery 
replacement mode. When “

” is displayed, the activation is 

completed.

*

Activate the battery replacement mode while the “input power 
supply” is turned ON.
If you replace the battery without activating the battery 
replacement mode, the battery life may not be detected 
accurately because the battery life counter is not reset.

Do not replace the battery during backup operation. Otherwise, the 
output stops.

The life of the battery used in the UPS is limited. This life changes 
depending on the use environment and the frequency of backup 
operation.

As the battery life comes closer to its end, the battery deteriorates 
more rapidly. Be careful.

The storage condition also affects the deterioration of the battery. As 
the storage temperature becomes higher, the battery life becomes 
shorter. Be careful.

Battery check schedule and frequency

Applicable directives

EMC Directives

Low Voltage Directives

Principles regarding conformance

OMRON electronic devices that comply with EC Directives also 
conform to the related EMC standards so that they can be more easily 
built into other devices or the overall machine. The actual products 
have been checked for conformity to EMC standards*.
Whether the products conform to the standards in the system used by 
the customer, however, must be checked by the customer. EMC-
related performance of the OMRON devices that comply with EC 
Directives will vary depending on the configuration, wiring, and other 
conditions of the equipment or control panel on which the OMRON 
devices are installed. The customer must, therefore, perform the final 
check to confirm that devices and the overall machine conform to 
EMC standards.

*

Applicable EMC (Electromagnetic Compatibility) standards are as 
follows: EMS (Electromagnetic Susceptibility): EN 61000-6-2, EMI 
(Electromagnetic Interference): EN 61000-6-4, and EN 61000-6-4 
Radiated emission: 10-m regulations

Low Voltage Directives

Always ensure that devices operating at voltages of AC 50 to 1,000 V 
and DC 75 to 1,500 V meet the required safety standards. The 
applicable directive is EN60950-1.

Conformance to EC Directives

This product complies with EC Directives. To ensure that the machine 
or device in which the this product is used complies with EC 
Directives, the product must be installed as follows:

This product must be installed within a control panel.

You must use reinforced insulation or double insulation for the 
direct power supply equipment connected to this product.

Models of this product that comply with EC Directives also conform 
to the Common Emission Standard. Radiated emission 
characteristics (10-m regulations), in particular, may vary 
depending on the configuration of the control panel used, other 
devices connected to the control panel, wiring, and other 
conditions. Therefore, even when using a model of this product 
that complies with EC Directives, you must confirm and ensure the 
compliance to EC Directives of the entire machine or equipment.

This is a Class A product (for industrial environments). In a 
residential environment, it may cause radio interference. If radio 
interference occurs, the user may be required to take appropriate 
measures.

Precautions for Correct Use

Do not stack

Do not mount on floor with 
front side down

To mount UPS on floor with its top side away 
from you, ensure that its top side is not in 
contact with wall.

Ambient 

temperature

6-Month Inspection

3-Month Inspection

55°C

Up to 1 year from the 
date of purchase

1 year from the date 
of purchase and 
afterward

50°C

Up to 1.5 years from 
the date of purchase

1.5 years from the 
date of purchase and 
afterward

40°C

Up to 3 year from the 
date of purchase

3 years from the date 
of purchase and 
afterward

25°C

Up to 6 year from the 
date of purchase

6 years from the date 
of purchase and 
afterward

Conformance to EC Directives

Summary of Contents for S8BA LF Series









































Reviews: