background image

K3NC

K3NC

2

3

MODEL NUMBER LEGEND

K3NC -

1

2

3

4

Base Units

1, 2. Input Sensors Codes

NB: NPN inputs
PB: PNP inputs

3. Supply Voltage

1: 100 to 240 VAC
2: 12 to 24 VDC

4. Display

A: Basic Model
C: Set Value LED Display

Specifications

3

RATINGS

Supply voltage

100 to 240 VAC (50/60 Hz); 12 to 24 VDC

Operating voltage range

85% to 110% of supply voltage

Power consumption (See Note.)

15 VA max. (max. AC load with all indicators lit)
10 W max. (max. DC load with all indicators lit)

Sensor power supply

80 mA at 12 VDC

±

10%

Insulation resistance

20 M

min. (at 500 VDC) between external terminal and case.

Insulation provided between inputs, outputs, and power supply.

Dielectric withstand voltage

2,000 VAC for 1 min between external terminal and case.
Insulation provided between inputs, outputs, and power supply.

Noise immunity

±

1,500 V on power supply terminals in normal or common mode

±

1

µ

s, 100 ns for

square-wave noise with 1 ns

Vibration resistance

Malfunction: 10 to 55 Hz, 0.5-mm for 10 min each in X, Y, and Z directions
Destruction: 10 to 55 Hz, 0.75-mm for 2 hrs each in X, Y, and Z directions

Shock resistance

Malfunction: 98 m/s

2

(10G) for 3 times each in X, Y, and Z directions

Destruction: 294 m/s

2

(30G) for 3 times each in X, Y, and Z directions

Ambient
t

t

Operating

--10 to 55

°

C (14 to 131

°

F) with no icing

temperature

Storage

--20 to 65

°

C (--4 to 149

°

F) with no icing

Ambient humidity

Operating

25% to 85% (with no condensation)

Ambient atmosphere

Must be free of corrosive gas

EMC

Emission Enclosure:

EN55011 Group 1 class A

Emission AC Mains:

EN55011 Group 1 class A

Immunity ESD:

EN61000-4-2:4-kV contact discharge (level 2)

8-kV air discharge (level 3)

Immunity-RF-interference:

ENV50140:

10 V/m (amplitude modulated, 80 MHz to
1 GHz) (level 3)
10 V/m (pulse modulated, 900 MHz)

Immunity Conducted Disturbance:

ENV50141:

10 V (0.15 to 80 MHz) (level 3)

Immunity Burst:

EN61000-4-4:2-kV power-line (level 3)

2-kV I/O signal-line (level 4)

Approved standards

UL508, CSA22.2, CE; conforms to EN50081-2, EN50082-2, EN61010-1 (IEC1010-1);
conforms to VDE106/part 100 (Finger Protection) when the terminal cover is mounted.

Weight

Approx. 400 g

Note: An Intelligent Signal Processor with DC supply voltage requires approximately 1 A DC as control power supply current the moment

the Intelligent Signal Processor is turned on. Do not forget to take this into consideration when using several Intelligent Signal
Processors. When the Intelligent Signal Processor is not in measuring operation (e.g., the Intelligent Signal Processor has been
just turned on or is operating for startup compensation time), the display will read “

ööööö

” and all outputs will be OFF.

Summary of Contents for K3NC













Reviews: