background image

K3HB-X

12

Input Compensation/Display

Forces the present value to 0. (Convenient for setting reference val-
ues or deducting tares for weight measurement.)

Compensates for mild fluctuations in input signals due to factors
such as sensor temperature drift, based on OK (PASS) data at mea-
surement. (This function can be used with sampling hold, peak hold,
or bottom hold.)

Changes the display value to 0 for input values less than the set
value. It is enabled in normal mode only. (This function can be used,
for example, to stop negative values being displayed or to eliminate
flickering and minor inconsistencies near 0.)

The display refresh period can be lengthened to reduce flickering
and thereby make the display easier to read.

Values can be displayed in either red or green. With comparative out-
put models, the display color can also be set to change according to
the status of comparative outputs (e.g., green to red or red to green).

The current display value can be selected from the present value, the 
maximum value, and the minimum value.

It is possible to specify (i.e., restrict) the values that the smallest dis-
played digit can change by. For example, if the setting is 2, the small-
est digit will only take the values 0, 2, 4, 6, or 8 and if the setting is 5,
it will only take the values 0 or 5. If the setting is 10, it will only take
the value of 0.

The minimum and maximum values when the power supply is 
turned OFF can be saved if interruption memory is turned ON.

If interruption memory is ON, the maximum and minimum values 
after the last resetting will be displayed.  

If interruption memory is OFF, the maximum and minimum values 
will be displayed after the power supply is turned ON (or after the 
reset input is performed).  

Forced-zero

Zero-trimming

Zero-limit

Display Refresh Period

Display Color Selection

Zero-limit

setting

Display

Inp

u

t

110.01

Red

Red

Comparati

v

e set 

v

al

u

e L

Comparati

v

e set 

v

al

u

e H

110.00

100.05

110.00

99.87

110.00

L

Example) Setting: 

grn-r

H

P

Green

Display Value Selection

Step Value

Interruption Memory 

Summary of Contents for K3HB-X


















Reviews: