background image

10

H7CZ

Operating Procedures

Setting Procedure Guide

Run mode

Power ON

Function 

setting mode

Note:

 Displayed only when the output mode is C, R, K-1, P, Q, or A.

3 s min. 

*

2

3 s min. 

*

1

Change to Function Setting Mode. 

Input mode 
(CNTM)

Output 
time 
(OTIM)

Output mode 
(OUTM)

(1 ms)

(20 ms)

(No decimal 

point)

Prescale 
value 
(PSCL)

Counting 
speed 
(CNTS)

(30 Hz)

(5 kHz)

The characters displayed in reverse video are the default settings.

(N)

(F)

(C)

(R)

(K-1)

(P)

(Q)

(A)

(DOWN)

(UP)

(99.999)

(1.000)

(0.001)

(0.50 s) (99.99 s)

(0.01 s)

To next page

From next page

Reset input 
signal width 
(IFLT)

Decimal 
point position 
(DP)

• Set the input mode using the 

U

 Key.

• Set the output mode using the 

U

 Key.

• Set each digit using the individual 

U

 Key.

• Set the counting speed using the 

U

 Key.

• Set the Reset input signal width using the 

U

 Key.

• Set the decimal point position using the 

U

 Key.

(One digit after 

decimal point)

(Two digits after 

decimal point)

(Three digits after 

decimal point)

• Set each digit using the individual 

U

 Key.

*

Function Settin

g

 Mode

up

down

n

f

0.01

99.99

0.50

30hz

1ms

0.001

99.999

1.000

20ms

c

r

k-1

p

q

a

*1.

 

If the mode is switched to the function setting mode during operation, operation will continue.

*2.

 

Changes made to settings in function setting mode are enabled for the first time when the mode is changed to run mode. Also, 

when settings are changed, the counter is reset (present value initialized and output turned OFF) on returning to run mode.

*

 

The display shows 5 kHz, but the maximum counting speed is 10 kHz.

For details on operations and display in r

u

n mode, refer to page 13. 

The display depends on the selected config

u

ration.

Summary of Contents for H7CX-R11D1





















Reviews: