background image

H7CZ

12

Explanation of Functions

Input Mode (

cntm

)

Set increment mode (UP) or decrement mode (DOWN) as the input 
mode.

Output Mode (

outm

)

Set the way that control output for the present value is output. The 
possible settings are N, F, C, R, K-1, P, Q, and A.

One-shot Output Time (

otim

)

Set the one-shot output time (0.01 to 99.99 s) for control output.
One-shot output can be used only when C, R, K-1, P, Q, or A is 
selected as the output mode.

Counting Speed (

cnts

)

Set the maximum counting speed (30 Hz/5 kHz) for count inputs.

Reset Input Signal Width (

iflt

)

Set the reset input signal width (20 ms/1 ms) for reset inputs.
If contacts are used for the input signal, set the input signal width to 
20 ms. Processing to eliminate chattering is performed for this setting.

Decimal Point Position (

dp

)

Decide the decimal point position for the present value.

Prescale Value (

pscl

)

Pulses input to the counter are converted according to the specified 
prescale value.
(Setting range: 0.001 to 99.999 for 6-digit models.)
Example: To display the feed distance for systems that output 25 
pulses for a feed length of 0.5 m in the form 

@@

.

@@

 m:

1. Set the decimal point position to 2 decimal places.
2. Set the prescale value to 0.02 (0.5 

÷

 25).

• Observe the following points when setting a prescale value. 

Set the set value to a value less than {Maximum countable value 

 Prescale value}.

Example: If the prescale value is 1.25 and the counting range is 
0.000 to 999.999, set the set value to a value less than 998.749 
(= 999.999 

 1.25).

If the set value is set to a value greater than this, output will not turn 
ON. 

• Output will turn ON, however, if a present value overflow occurs 

(FFFFFF).

Set Value Upper Limit (

sl-h

)

Set the upper limit for the set value when it is set in run mode.
The setting can be made from 1 to 999999 for 6-digit models. 

Key Protect Level (

kypt

)

Set the key protect level.
Refer to 

Key Protect Level

 on page 16.

Output ON Count Alarm Set Value (

on-a

)

Set the alarm value for the output ON count.
The limit can be set to between 0 

×

 1000 (0 times) and 9999 

×

 1000 

(9,999,000 times). Only the underlined values are set. The alarm will 
be disabled if 0 is set. 
If the total ON count of the output exceeds the alarm set value,  

e3

 

will be displayed on the Timer to indicate that the output ON count 
alarm value was exceeded. Refer to 

Self-diagnostic Function

 on 

page 16 for information on the 

e3

 display. 

Output ON Count Monitor Value (

on-c

)

The monitor value is only displayed. It cannot be set. 
The output ON count will be 1,000 times the displayed value. 

25 pulses

Encoder

0.5 m

Note:

If the prescale value setting is incorrect, a counting error will 
occur. Check that the settings are correct before using this 
function.

Summary of Contents for H7CX-R11D1





















Reviews: