*The camera cable is polarized, so, make sure that the end bearing a
name plate is connected to the Controller.
*When connecting the camera cable, tighten the cable with the fixing
screw with the recommended torque (0.15 N
・
m). Applying excessive
force to the camera connector may cause failure of the product.
*Use the ferrite core equivalent to ZCAT2035-0930A (manufactured by
TDK) at the controller side of the camera cable, when using this
camera with FH controller.(except for FH-L series)
FZ-SC5M3/S5M3
2017
Manufacturer:
OMRON Corporation,
Shiokoji Horikawa, Shimogyo-ku,
Kyoto. 600-8530 JAPAN
TRACEABILITY INFORMATION:
Importer in EU:
Omron Europe B.V.
Wegalaan 67-69,
NL-2132 JD Hoofddorp
The Netherlands
5 MEGA PIXEL DIGITAL CAMERA FOR
MODEL FZ/FH VISUAL INSPECTION SYSTEM
.
FZ-SC5M3/S5M3
2.6W max. (13V DC)
Approx. 85g (including base)
0 dB to 18 dB
4 lines to 2048 lines
2448(H)×2048(V)
FZ-SC5M3
2/3-inch color CMOS 2/3-inch monochrome CMOS
FZ-S5M3
25.6fps
PRECAUTIONS FOR CORRECT USE
Please observe the following precautions to prevent failure to
operate, malfunction, or undesirable effect.
･
Be sure to turn off the power before connecting or
disconnecting the cables.
･
Do not use the camera cable exceeding the specified length.
(1) Connecting Cables
(3) Others
･
Do not use unspecified camera cable and a strobe controller
other than those that specified in this manual with the FZ
controller. Connection with unspecified camera cable and/or
strobe controller may malfunction at the worst case.
･
Do not put an impossible stress on the camera cable when you
set it up. The cable is disconnected, and it becomes impossible
might do a normal measurement.
･
If you do not use the enhancing connector on the back of the
camera, do not remove the cap that is attached to the connector.
･
Do not attempt to dismantle, repair, or modify the main body.
･
If you suspect an error or malfunction, stop using the Controller
immediately, turn OFF the power supply, and consult your
OMRON representative.
･
Dispose of FZ-S2M components as industrial waste.
(2) Handling the Camera
Make sure to tighten all installation screws securely.
The Camera’s case is connected to the 0V line in the internal
circuits. Observe the following precautions to prevent noise
interference.
･
Do not ground the Camera.
･
Do not remove the base attached to the Camera.
The center of the optical axis varies with the camera used.
Therefore, when installing the camera, always check the center
of the image displayed on the monitor.
(2) Optical axis of the Camera.
･
If large dust particles adhere to the the imaging element, use a
blowerbrush (used to clean camera lenses) to blow them off.
Do not blow the dust particles with your mouth.
･
Avoid using thinner, alcohol, benzene, acetone or kerosene to
clean the product.
(3) Maintenance
Suitability for Use
s
Omron Companies shall not be responsible for conformity with any standards,
codes or regulations which apply to the combination of the Product in the
Buyer’s application or use of the Product. At Buyer’s request, Omron will
provide applicable third party certification documents identifying ratings and
limitations of use which apply to the Product. This information by itself is not
sufficient for a complete determination of the suitability of the Product in
combination with the end product, machine, system, or other application or
use. Buyer shall be solely responsible for determining appropriateness of the
particular Product with respect to Buyer’s application, product or system.
Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING
SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE
SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND
INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL
EQUIPMENT OR SYSTEM.
See also Product catalog for Warranty and Limitation of Liability.
Oct, 2014
D
OMRON Corporation
Industrial Automation Company
Contact: www.ia.omron.com
Tokyo, JAPAN
OMRON ELECTRONICS LLC
2895 Greenspoint Parkway, Suite 200
Hoffman Estates, IL 60169 U.S.A.
Tel: (1) 847-843-7900/Fax: (1) 847-843-7787
OMRON ASIA PACIFIC PTE. LTD.
No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Alexandra Technopark,
Singapore 119967
Tel: (65) 6835-3011/Fax: (65) 6835-2711
OMRON (CHINA) CO., LTD.
Room 2211, Bank of China Tower,
200 Yin Cheng Zhong Road,
PuDong New Area, Shanghai, 200120, China
Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200
OMRON EUROPE B.V.
Sensor Business Unit
Carl-Benz-Str. 4, D-71154 Nufringen, Germany
Tel: (49) 7032-811-0/Fax: (49) 7032-811-199
Regional Headquarters
2448(H)×2048(V)
3.45(
μ
m)×3.45(
μ
m)
Non-interlace mode
25.6fps
4 lines to 2048 lines
Internal Sync.
Digital (10bit)
0 to 24dB
1/10 to 1/50000s
C mount
Effective pixels
Pixel size
Scanning method
Frame rate
Number of lines to be read
Synchronization
Video output
Gain
Shutter speed
Lens mounting
40.7
10.5
1
30Dia.
36Dia.
34
7
35
4-R2.5
35
1"-32UNF(C MOUNT)
22.7
14.5
25
16.8
4-M4 DEPTH4
（THREE COMMONNESS）
31.7
9.5
9.5
15.5
10
2-M4 DEPTH5.5
1/4" 20UNC DEPTH5.5
2-4.5Dia.
19±0.1
MOUNTING SCREW HOLES
