75
Revision History
A manual revision code appears as a suffix to the catalog number on the front cover of the manual.
Cat. No. I005-E1-2
Revision code
The following table outlines the changes made to the manual during each revision. Page numbers refer to the
previous version.
Revision code
Date
Revised content
1
March 1993
Original production
1A
July 1993
Page 5: Data in the table has been corrected.
Pages 9, 11, 12: Inverter capacities in the tables have
been corrected.
Pages 21, 23: Output characteristics’ inverter capaci-
ties in the tables have been corrected.
Pages 22, 24: Weight data in the tables has been
corrected.
1B
March 1994
Pages 7, 14: Terminal 8 in the wiring diagram cor-
rected to 0 to +10 VDC
(2 K
Ω
).
Page 37: First digit of constant no. 1 corrected to ter-
minals 8 and 9.
Page 47: Third digit for constant no. 18 corrected to
reflect that it is not used.
Page 57: Set values in the heading for Search Com-
mand corrected to “Set Value = 9, 10.”
1C
January 1996
Page 3: “Enclosed type” and “open-chassis type”
changed to “with top cover on” and “with top cover off,”
respectively.
Page 13: “Power supply coordination AC reactor”
replaced with “AC reactor.” Diagram corrected.
Page 21: Stall prevention level specification corrected.
Page 25: Radio noise protective filter function cor-
rected.
Page 29: Constants that can be changed in DRIVE
Mode have been added.
Page 33: Row where 00 = 5 added.
Page 34: Note 2 added.
Page 37: Set value 5 added to No. 0.
Page 38: References to note 2 added to No. 9 to No.
12.
Page 39: Setting range of torque compensation
increased to 9.0. Note 2 added.
Page 40: Set values added to No. 32 and No. 33. Ini-
tial setting for No. 33 corrected to 3.
Page 41: 2
nd
digit for constant 46 added. PROM No.
added for constant 49.
Page 42: No. 57 to No. 59 and No. 67 added. Note 1
deleted.
Page 50: Set values and note 4 added.
Page 51:
Local/Remote Operation and UP/DOWN
Command added.
Page 56:
2-8-22 Enable/Disable Setting Constants in
DRIVE Mode added.
Page 59:
2-8-26 Slip Compensation Speed Control
and
2-8-27 Inverter Overload Protection added.
2
November 1997
Model number suffix “-E” changed to “EV2” throughout the manual.
Page 3: “Potentiometers” corrected to “constants” in caution.
Page 9: Settings when a ground fault interrupter is used have been corrected in
Mold-
case Circuit Breaker (MCCB).
Page 10: Caution on withstand voltage added.
Page 13: “Acceptable” grounding example removed.
Page 24: Note added to
1-6-3 Optional Units.
Page 37: Setting range corrected for constant numbers 27 and 28 of “DC injection brak-
ing.”
Page 38: “5: Operation mode” added to constant numbers 34 and 35 of “Photocoupler
output signal.”
Page 39: 3
rd
digit information and note added to constant number 46. Initial setting cor-
rected.
Page 40: Descriptions for “Slip compensation speed control” (constant numbers 57 to
59) corrected. Factory settings added (constant numbers 60 to 66, 68, and 69).
Page 47: Information added to
2-8-12 Motor Stall Prevention Function.
Page 49: Information for
UP/DOWN Command changed.
Page 54:
2-8-21 Momentary Power Loss Protection changed to 2-8-21 Other Functions.
Page 56: “Residual voltage” corrected to “motor residual voltage’ in
Minimum Baseblock
Time (No. 55).
Page 58: Information in
2-8-27 Slip Compensation Speed Control changed and added
to. Note added to
2-8-28 Inverter Overload Protection.
Page 61: Information for the low voltage protection, overcurrent protection, and cooling
fin overheat protection functions corrected.
Pages 62, 63: “Simultaneous normal and reverse rotation commands” corrected to
“Simultaneous forward and reverse rotation commands.”
Page 63: Information for “Low-voltage protection (main circuit voltage insufficient)” and
“Simultaneous forward and reverse rotation commands” corrected.
