27
FI start selection
1085h
A105
00: Start frequency A101
01: 0 Hz
-
1287h
A105
00: FI Start Frequency (A101)
01: 0 Hz
-
Operation frequency input A
setting
108Eh
A141
12AFh
A141
Operation frequency input B
setting
108Fh
A142
12B0h
A142
Operator selection
1090h
A143
00: Addition (A + B)
01: Subtraction (A − B)
02: Multiplication (A × B)
-
12B1h
A143
00: Addition (A141 + A142)
01: Subtraction (A141 − A142)
02: Multiplication (A141 × A142)
-
12B3h A145(HIGH)
12B4h A145(LOW)
Frequency addition direction
1093h
A146
00: Adds the A145 value to the
output
-
12B5h
A146
00: Frequency ref A145
01: Frequency reference − A145
-
12C6h A161(HIGH)
12C7h A161(LOW)
12C8h A162(HIGH)
12C9h A162(LOW)
VR start ratio
1098h
A153
0 ～ 100
1[%]
12CAh
A163
0 to VR End Ratio
1[%]
VR end ratio
1099h
A154
0 ～ 100
1[%]
12CBh
A164
VR Start Ratio to 100
1[%]
VR start selection
109Ah
A155
0, 1
-
12CCh
A165
00: VR Start Frequency (A161)
01: 0 Hz
-
Retry selection
10A5h
b001
00: Alarm
01: 0 Hz start
02: Frequency matching restart
03: Trip after frequency matching
deceleration stop
-
1301h
b001
00: Trip
01: 0-Hz restart
02: Frequency matching restart
03: Trip after frequency matching
deceleration stop
04: Frequency pull-in restart
-
Allowable momentary power 10A6h
b002
3 ～ 250
0.1[s]
1302h
b002
3～250
0.1[s]
Retry wait time
10A7h
b003
3 ～ 1000
0.1[s]
1303h
b003
3～1000
0.1[s]
Momentary power
interruption/undervoltage
trip during stop selection
10A8h
b004
00: Disabled
01: Enabled
-
1304h
b004
00: Disabled
01: Enabled
02: Disabled during stop and
deceleration stop by turning off the
RUN command
-
Momentary power
interruption retry time
10A9h
b005
00: 16 times
01: No limit
-
1305h
b005
00: 16 times
01: No limit
-
Starting frequency at
frequency pull-in restart
1170h
b011
00: Frequency at interruption
01: Max. frequency
02: Set frequency
-
131Fh
b030
00: Frequency at interruption
01: Maximum frequency
02: Set frequency (Frequency
reference)
-
Electronic thermal level
10ADh
b012
130Dh
b012
2nd electronic thermal level
1527h
b212
230Ch
b212
Electronic thermal
characteristics selection
10AEh
b013
130Eh
b013
2nd electronic thermal
characteristics selection
1528h
b213
230Dh
b213
Overload limit selection
10B5h
b021
1316h
b021
2nd overload limit selection
1529h
b221
2316h
b221
Overload limit level
10B6h
b022
1317h
b022
2nd overload limit level
152Ah
b222
2317h
b222
Overload limit parameter
10B7h
b023
1318h
b023
2nd overload limit parameter 152Bh
b223
2318h
b223
Deceleration rate constant
1171h
b029
1 ～ 30000
0.1[s]
131Eh
b029
1～30000
0.1[s]
Frequency pull-in restart
1172h
b030
200 ～ 20000
0.01[%]
131Dh
b028
200～2000
0.1[%]
Soft lock selection
10BCh
b031
00: Data other than b031 cannot be
changed when terminal SFT is ON.
01: Data other than b031 and the
specified frequency parameter
cannot be changed when terminal
SFT is ON.
02: Data other than b031 cannot be
changed.
03: Data other than b031 and the
specified frequency parameter
cannot be changed.
10: Data other than parameters
changeable during operation cannot
be changed.
-
1320h
b031
00: Data other than b031 cannot be
changed when terminal SFT is ON.
01: Data other than b031 and the
set frequency cannot be changed
when terminal SFT is ON.
02: Data other than b031 cannot be
changed.
03: Data other than b031 and set
frequency cannot be changed.
10: Data can be changed during
RUN.
-
Selection of non-stop
function at momentary
power interruption
10C9h
b050
00: Disabled
01: Enabled (Stop)
02: Enabled (Restart)
-
1334h
b050
00: Disabled
01: Enabled (Deceleration stop)
02: Enabled (Constant voltage,
without recovery)
03: Enabled (Constant voltage, with
recovery)
-
Starting voltage of non-stop
function at momentary
power interruption
10CAh
b051
0 ～ 10000
0.1[V]
1335h
b051
0～10000
0.1[V]
Stop deceleration level of
non-stop function at
momentary power
interruption
10CBh
b052
0 ～ 10000
0.1[V]
1336h
b052
0～10000
0.1[V]
1337h b053(HIGH)
1338h b053(LOW)
Deceleration starting width
of non-stop function at
momentary power
interruption
10CEh
b054
0 ～ 100
0.1[Hz]
1339h
b054
0～1000 (In the high-frequency
mode︓10000)
0.01[Hz]
Overvoltage protection
proportional gain during
deceleration
1173h
b055
2 ～ 50
0.1
1388h
b133
0～500
0.01
Overvoltage protection
integral time during
deceleration
1174h
b056
0 ～ 1500
0.1[s]
1389h
b134
0～1500
0.1[s]
0.01[s]
1 ～ 300
0.1[s]
1～30000
0.1[s]
Deceleration time of nonstop
function at momentary
10CCh
b053
1 ～ 30000
0.1[s]
1～360000
00: Disabled
01: Enabled in acceleration/constant
-
00: Disabled
01: Enabled during
-
00: Disabled
01: Enabled in acceleration/constant 0.01[%]
200～2000
0.1[%]
0.01[Hz]
2000 to 10000
Set the rated current to 10000
0.01[%]
200～1000
0.1[%]
00: Reduced torque characteristics 1
01: Constant torque characteristics
02: Reduced torque characteristics 2
-
00: Reduced torque characteristics
01: Constant torque characteristics
02: Free setting
-
VR end frequency
1097h
A152
0 ～ 4000
0.1[Hz]
0～40000 (In the high-frequency
mode︓～58000)
0.01[Hz]
VR start frequency
1095h
A151
0 ～ 4000
0.1[Hz]
0～40000 (In the high-frequency
mode︓～58000)
0.01[Hz]
00: Digital Operator (F001)
01: Digital Operator (volume)
02: Input FV
03: Input FI
04: RS485 communications
-
00: Digital Operator (A020/A220)
01: Volume
02: Voltage (FV) input
03: Current (FI) input
04: Modbus communication
05: Option
07: Pulse train frequency
-
Frequency addition amount
1091h
A145
0 ～ 4000
0.1[Hz]
0～40000 (In the high-frequency
mode︓～58000)
