OmniCell OmniTrack Installation Manual Download Page 8 | Manualshive

Page: 8 / 16

background image

1-4

OmniTrack Installation and Programming Instructions

Reassembling the OmniTrack

OmniTrack Installation Guide

/67-2055 Rev A

© 2009 Omnicell, Inc.

2. Connect each of the 32 button bar cable connectors to the controller board.

Figure 1-5.

Figure 1-6.

3. Connect the “controller to SPC” (part # 42-7015) cable to the controller, or when installing the

OmniTrack directly above the PC Box, connect the flex connector (part # 42-31230).

Note:

Wires must be connected and not rearranged. Note the orientation of PCBA within the extrusion.

«
...
6
7
8
9
10
...
»

Summary of Contents for OmniTrack

















Reviews:

No comments

Related manuals for OmniTrack

Brand: ABB Pages: 370

Brand: ABB Pages: 17

Brand: ABB Pages: 104

Brand: ABB Pages: 120

Brand: ABB Pages: 42

Brand: JDS Uniphase Pages: 27

Brand: Danfoss Pages: 20

Brand: OEG Pages: 168

Brand: Watts Pages: 2

Brand: Hanbay Pages: 18

Brand: BabySafe Pages: 24

Brand: Barco Pages: 6

Brand: VAT Pages: 26

ESD-5550 Series

Brand: GAC Pages: 12

Brand: Quectel Pages: 90

Brand: OJ Electronics Pages: 8

Brand: OJ Electronics Pages: 112

Brand: OJ Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands