background image

 21 

 

SECTION 8. SERVICE 

8.1 A

SSISTANCE

 

Should this product ever require service, please contact Omni International at 

1–800–776-4431. 

8.2 D

ECONTAMINATION

 

Should an instrument or component that has been used with radioactive or 
pathogenic material require factory or field service, comply with the following 

procedure to ensure the safety of service personnel: 

 

• 

Clean the parts to be serviced of all encrusted material and  

      decontaminate them. There must be no radioactivity detectable by survey    
      equipment. 

• 

Obtain a Decontamination Certificate from Omni International.        

Complete the certificate and attach to the instrument or parts being   

returned. 

 

If no Decontamination Certificate is attached, and a potential radioactive or 

biological hazard is detected or suspected by Omni International, the  
equipment will not be serviced until proper decontamination and certification 

is complete. The sender will be contacted for instructions as to the  

disposition of the equipment. Disposition costs will be borne by the sender. 

WARNING: 

It is a violation of federal law to transport biologically  

hazardous or radioactive materials without proper packaging, labeling, and 

appropriate warnings. 

Summary of Contents for Omni Mixer

























Reviews: