Page - 7
Page - 14
Feature #3 Confirmation Chirp Function & Volume
Factory Default Setting
Low
(
press
“lock” button to program
)
Options:
High (loudest)
(
press
“unlock” button to program
)
On Demand / High
(
press
“trunk” button to program
)
OFF (no chirps)
(
press
“start” button to program
)
This feature allows the choice of two different volume levels of the system’s con-
firmation chirps and the ability to turn OFF chirps or have them on demand. When
programming, the you can hear and choose the setting with the best chirp volume.
The “On Demand” setting allows you to lock and unlock the doors without chirps.
Pressing either function a 2nd time, will produce confirmation chirps.
Feature #4 Steady Siren or Pulsed Horn
Factory Default Setting
Pulsed Horn Low
(
press
“lock” button to program
)
Options:
Pulsed Horn Medium
(
press
“unlock” button to program
)
Pulsed Horn High
(
press “trunk” button to program
)
Steady Siren
(
press
“start” button to program
)
This feature changes only the audible output, in three different pulse timings, which
allow a degree of customizing of the horn’s sound during the alarm activation. The
Steady Siren setting is exactly that- a steady output which an optional electronic
siren would require.
Feature #2 Steady/Flashing Lights During Remote Start
Factory Default Setting
Steady (
press
“lock” button to program
)
Option:
Flashing (
press
“unlock” button to program
)
This Feature configures the operation of the vehicle’s parking lights during the
remote start operation. The default setting turns on the parking lights during remote
start; the other setting flashes the parking lights on and off during remote start.
Feature #1 Remote Start Run Time
Factory Default Setting
10 Minutes
(
press
“lock” button to program
)
Options:
5 Minutes
(
press
“unlock” button to program
)
15 Minutes
(
press “trunk” button to program
)
20 Minutes
(
press
“start” button to program
)
This feature sets the period of time that the engine will run after being remotely
started. If the engine is not stopped by controller/transmitter command or a safety
circuit violation, the engine will automatically stop upon the expiration of the
selected time period. Caution: The remote engine starting feature should
NEVER be used when the vehicle is parked in an enclosed structure or garage.
THE PARKING
LIGHTS WILL FLASH
REPEATEDLY
THE DOORS WILL LOCK or
UNLOCK
To Activate Panic Mode:
Press & Hold the LOCK or UNLOCK button for 3 seconds
•
The horn will sound, the parking lights will flash and
the doors will lock or unlock, depending on the trans-
mitter button used. To deactivate Panic, simply press
either the LOCK or UNLOCK button again- Panic stops
with either locked doors or unlocked doors, depend-
ing on which button is used.
Valet Mode
The system may be placed into a “valet mode” which prevents the
remote start feature from being activated. It also disables confirmation
chirps when locking or unlocking the doors. Valet Mode should always be
used when you do not wish for remote starting to be operated, such as
when you have your vehicle serviced or leave it with someone else. The
Valet Switch, is used to engage Valet Mode:
•
With the system in an unlocked state, simply press and hold the Valet
Switch for 3 seconds; the optional Status Light will light steady, to indicate
Valet Mode, and stay illuminated continuously while the system is in Valet
Mode. The horn will chirp once and the lights will flash twice.
Once in Valet Mode, an attempt to remote start will result in no response
from the system. Keep this in mind if remote start stops functioning. The
system may have accidentally been placed in valet mode. To check for
valet mode, turn the ignition key to the RUN/ON position, then back OFF.
If the system is in valet mode, the horn will chirp once.
•
To turn off Valet Mode, simply press & release the Valet Switch once.
The optional Status Light will turn off.
Valet Mode only prevents the remote starting operation; the lock, unlock,
and trunk release functions all continue to operate when in Valet Mode.
Emergency Override
If the system is in a locked state, you cannot perform some functions
like transmitter or feature programming. If the system is locked and you do
not have a transmitter to unlock the system, you can perform an emer-
gency override to access the programming functions.
Using The Valet Switch
OR
