Omega OAL-100 User Manual Download

Page: 1 / 25

background image

OMEGA AUTOMATICS 2020 v3.0.2

1

OAL-100 INSTALLATION INSTRUCTIONS

WARNING!

READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS CAREFULLY!

FAILURE TO DO SO MAY RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE!

AVOID ELECTRICAL SHOCK
DISCONNECT POWER DURING INSTALLATION
PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION
POWER SUPPLY REQUIRED 115+/- 5VAC-60 HZ 0.4 AMPS
CONTROL BOARD POWER SUPPLY 16VDC
CONTROL BOARD TO BE GROUNDED
KEEP FINGERS & CLOTHING CLEAR OF ALL MOVING PARTS
ADJUSTMENTS TO BE PERFORMED BY APPROVED TECHNICIAN ONLY
ALTERATION TO ANY COMPONENTS IS PROHIBITED
REMOVE ANY MECHANICAL DEVICES OR LOCKS THAT INTERFERE WITH THE
OPERATION OF THE DOOR, (OTHER THAN PARTS INTEGRATED WITH THE OPERATOR
SYSTEM)
OPERATOR TO BE INSTALLED 8 FEET MINIMUM ABOVE GROUND IF THERE ARE ANY
EXPOSED MOVING PARTS

1
2
3
...
»

Summary of Contents for OAL-100


























Reviews:

No comments

Related manuals for OAL-100

Brand: Cal-Royal Pages: 4

Brand: hager Pages: 10

Brand: hager Pages: 8

Brand: Yale Pages: 72

Brand: Nabco Pages: 10

Brand: Nabco Pages: 43

Brand: Nabco Pages: 50

Brand: Cal-Royal Pages: 4

Brand: Yale Pages: 10

Brand: FAAC Pages: 4

Brand: CAME Pages: 104

Brand: Cal-Royal Pages: 40

Brand: Abus Pages: 2

Brand: raumplus Pages: 23

Brand: hager Pages: 6

Brand: hager Pages: 6

Brand: Cal-Royal Pages: 3

Brand: Yale Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands