Page 29
#8 Doors Lock With Automatic Rearming:
Default Off
This feature adds the automatic locking of the doors to feature #5, Automatic
Rearming. If this feature is turned on, the doors will lock when the system rearms
itself 90 seconds after being disarmed by the transmitter. Feature #6 must be
turned on for this feature to operate.
Programming Doors Lock With Automatic Rearming:
Follow Steps 1 to
4 on page 25; at Step 4 the Valet Switch will be pressed and released eight times.
The system’s response will be eight siren chirps, and the Status Light flashing eight
times, pausing, then repeating. Within 10 seconds, press and release the transmitter’s
"Arm/Lock" button to turn this feature on (the siren will chirp once) or the "Disarm/
Unlock" button to turn this feature off (the siren will chirp twice).
#9 Doors Lock When Ignition Is Turned On:
Default On
This feature configures the system to automatically lock the vehicle’s doors
every time that the ignition switch is turned on. An exception to this would be if
feature #12 is turned on, and a door being open when the ignition switch is turned
on. The two following features, #10 and #11, control the automatic unlocking
operation.
Programming Doors Lock When Ignition Is Turned On:
Follow Steps 1
to 4 on page 25; at Step 4 the Valet Switch will be pressed and released nine times.
The system’s response will be nine siren chirps, and the Status Light flashing nine
#7 Doors Lock With Last Door Arming:
Default Off
This feature adds the automatic locking of the doors to feature #4, Last Door
Arming. If this feature is turned on, the doors will lock when the system becomes
armed 30 seconds after closing the last door. Feature #4 must be turned on for this
feature to operate.
Programming Doors Lock With Last Door Arming:
Follow Steps 1 to 4 on
page 25; at Step 4 the Valet Switch will be pressed and released seven times. The
system’s response will be seven siren chirps, and the Status Light flashing seven
times, pausing, then repeating. Within 10 seconds, press and release the transmitter’s
"Arm/Lock" button to turn on the Doors Lock With Last Door Arming feature (the
siren will chirp once) or the "Disarm/Unlock" button to turn off the feature (the siren
will chirp twice).
Programming Ignition Activated Override:
Follow Steps 1 to 4 on page 25;
at Step 4 the Valet Switch will be pressed and released six times. The system’s
response will be six siren chirps, and the Status Light flashing six times, pausing,
then repeating. Within 10 seconds, press and release the transmitter’s "Arm/Lock"
button to turn on the Ignition Activated Override feature (the siren will chirp once)
or the "Disarm/Unlock" button to turn off the Ignition Activated Override feature
(the siren will chirp twice).
Page 16
The remote starting operation is as follows:
1- Press and release the transmitter’s “Arm/Lock” and “Disarm/Unlock” buttons.
The system will respond first by rapidly flashing the Status Indicator Light
Green, then by turning on the ignition and flashing the parking lights once.
2- The starter will engage until the engine runs; 10 seconds later the parking
lights will illuminate steady during the period that the engine is running
from being remotely started. (having them flash instead is an option).
The engine will run for 10 minutes (the factory-set period). A 20 minute setting
may be programmed, if desired, by referring to the “Programming Features”
section. Once the engine has been remotely started, to remotely stop it again press
and release together the transmitter’s “Arm/Lock” and “Disarm/Unlock” buttons.
The system will stop the engine, and extinguish the parking lights.
•
When leaving the vehicle before remote starting, remember to set the climate
controls to the desired heating or air conditioning settings.
•
If desired, the system’s alarm function may be armed or disarmed as needed
during remote start operations (the system must be disarmed before entering
the vehicle).
Should the engine fail to start on the first attempt, the system will subsequently
make as many as three further attempts, as needed. Please note that each starting
attempt takes approximately 20 seconds for the system to check the vehicle’s status,
cycle the ignition and starter circuits, and then monitor vehicle status again before
the next attempt.
Press & Release the “Arm/Lock” Button ( ) and the “Disarm/Unlock”
Button ( ) together
To Activate Remote Starting:
J
U
THE PARKING LIGHTS
WILL ILLUMINATE*
AND
THE ENGINE
STARTS
* FLASHING PARKING
LIGHTS IS OPTIONAL
