background image

5

To Lock the Vehicle's Doors:  Press & Release the left transmitter LOCK

button

Locking  &  Unlocking  the  Doors

To Unlock the Vehicle's Doors:  Press & Release the right transmitter

                UNLOCK button

• 

The parking lights flash twice then stay on for 30 seconds to confirm
unlocking, and optionally the horn will chirp twice.  The Status Light
on the Receiver Unit will have two long flashes when an unlock signal
is received.

The parking lights flash once to confirm locking, and optionally, the
horn will chirp once.  The Status Light on the Receiver Unit will have
one long flash when a lock signal is received.

*

*

THE PARKING

LIGHTS WILL FLASH

ONCE

THE DOORS WILL LOCK

THE PARKING

LIGHTS WILL FLASH

TWICE

THE DOORS WILL UNLOCK

The MARS is equipped with a horn/siren output; its connection is optional and may require extra parts.

operate the vehicle’s on-board doorlocking relays.  If the vehicle’s Negative pulse
doorlocking system requires more than  500mA Negative output, optional relays must
be used.

This doorlock system is similar to the 3 wire negative pulse system except the doorlock
switches send +12 Volt pulses to operate the doorlock relays/control unit.

Examine the wires on the back of the doorlock switch:
1) One wire will show +12 Volts, regardless of the switch's position.
2) One wire will show +12 Volts only when the switch is pushed to "lock".

36

3 Wire Positive Pulse Systems

Negative Pulse System Using

Direct Connection

Green Wire To Switch

Door Lock Wire

Door Lock
   Switch

Blue Wire To Switch

Door Unlock Wire

Vehicle's Doorlock

Relay Control Unit

Unlock

Lock

Control
Module

Ground

2-Wire Connector

Doorlock

Actuators

+

Summary of Contents for MARS-22





















Reviews: