background image

Page 5

 Upon Disarm: • The siren will chirp twice. 

(4 chirps if alarm has activated & reset)

• The parking lights will flash twice. 

(4 times if alarm has activated)

• The doors will unlock. 

(If an optional interface is connected)

• The starter interrupt will disengage.
• The LED Status Indicator will turn “Off”, or begin flashing rapidly
  if the Automatic Rearming feature is programmed on. 

(page 16)

Note: If a protected zone is open when actively arming using the transmitter, the
system will still arm, but bypass the open zone until the zone is secured.

Automatic “Last Door Arming” is a programmable feature which allows the alarm
to arm itself and, if desired, lock the doors. If “On”, this convenient feature offers
a high level of security since the user does not need to actively arm the system
each time the vehicle is exited.  Any time a door is opened and closed:

1) The LED Status Indicator will begin flashing rapidly to confirm that the Last

Door Arming countdown has begun.

2) 30 seconds later the system will arm, chirping the siren once, and locking the

doors, if programmed to do so and if an optional interface is installed.  The LED
Status Indicator will begin flashing slowly to confirm that the system is armed.

To Passively Arm the System:

  

Open & Close a Door.

Page 6

Regardless of method, once the system is in a fully armed state it monitors all
protected zones, and if an intrusion attempt is detected it will activate, or “trigger”.
An activation consists of the following:

1) 

The electronic siren, or optionally the vehicle’s horn, will start sounding.

2)

 The exterior parking lights will flash on and off repeatedly.

An activation has a 30 (or 60) second duration unless the system is disarmed using
the transmitter or the Valet /Override switch. If all protected zones are secure at
the end of the activation, the system will stop and rearm itself to detect further entry
attempts. If a protected zone is still open at the end of the activation cycle, the
system will continue to reactivate for up to 3 additional cycles. After the fourth cycle
the system will again rearm, but bypass the violated zone until it is restored.

Note: The system can not Last Door Arm if a protected zone is open. If a vehicle
door is opened during the arming countdown, the countdown will stop and start
over again when the door is closed.
Note: “Automatic Rearming” (page 16) is a separate programmable operation
similar to Last Door Arming, and should not be confused with it.

If the System is Activated:

Page 7

Remote Panic Operation

    Upon Activating Panic:

• The siren sounds and parking lights flash.
• The vehicle’s doors will lock.

    Upon Deactivating Panic:

• The siren and parking lights stop.
• The system is disarmed.

The Panic cycle has a 60 second duration (regardless of the 30 or 60 second
activation setting) unless a transmitter is used to stop it. At the end of the 60
second cycle, the system will reset and be in the armed state.

   THE SIREN SOUNDS

 THE PARKING-LIGHTS

WILL FLASH

THE DOORS WILL LOCK/UNLOCK

(IF CONNECTED)

 To Activate Panic:  Press & Hold the Large Button for 3 Seconds.

 To Deactivate Panic:  Press & Release the Large Button.

Should it be needed in a threatening situation, the system can be activated re-
motely by using the transmitter.

The Auxiliary Channel

Page 8

Note: The Auxiliary Channel cannot be activated if the vehicle's ignition is "On".
Note: If the system is armed when the Auxiliary Channel is used, it will also dis-
arm. This is a programmable feature (pages 17-18).
Note: The Auxiliary Channel has output for as long as the Small Button is held.

The Auxiliary Channel may be used to operate an optional function. Possibilities
include trunk release, remote car starting, or a window roll-up interface. Please
see your Omega dealer for details on available options.

Valet  Mode  &  Emergency  Override

   OPERATE OPTIONAL

   CAR-START MODULE

         OPERATE OPTIONAL

             TRUNK RELEASE

OPERATE OPTIONAL WINDOW ROLL-UPS

To Activate the Auxiliary Channel:

   

 Press & Hold the Small Button

   for 3 Seconds.

The Valet/Override Switch can perform two distinct functions: accessing Valet
Mode and performing an Emergency Override of an armed system.

Summary of Contents for K9-Mundial













Reviews: