background image

7

Installation

Install and use the machine in a room that can be efficiently ventilated, and where the floor is smooth and 

compact and easy to clean.

WARNING:

 While the machine is operating, in order to obtain a product with the right thickness and humidity, 

avoid air currents which will cause precocious drying of the product together with its deterioration.

•  To ensure the necessary stability of the machine, check that the wheels rest firmly on the floor, otherwise 

move the machine slightly until the four wheels have been steadily laid on the ground. Lastly, clamp the 

wheel with the brake (Figure 1A).

•  Position the machine in the desired place with a free back space of around 50 centimeters and a side 

space of 70-80 centimeters (Figure 2) in order to guarantee easy use of the machine and its cleaning.

For machines fitted with a trolley:

•  Make sure that the brake provided is clamped by pulling the lever down (Figure 1B).

•  Check that the voltage of the machine, which is written on the identification label (Figure 3), matches the 

one foreseen by the system on your premises.

•  Attach the right plug to the machine power cable in order to make the electrical connection to the system.

WARNING:

 Have the plug fitted to the power supply by qualified personnel. Take the necessary precautions to 

prevent the cable from being crimped or damaged.

CUTTING UNIT ASSEMBLY

•  Remove the components in the tank.

•  Assemble the cutting unit, after removing the socket-head screw (Figure 4A) from the bearing. Then tighten 

the screws right down again (Figure 4).

•  Plug the unit into the power supply socket (Figure 4B) of the machine; let the safety coupling click in.

CONNECTION TO THE WATER SYSTEM

•  For machines supplied with an extrusion sleeve cooling system, connect the machine to the water system 

and install the sending tube, (when it is non-existant: use a tap, possibly with screw-control) to the outer 

part of the machine, in order to regulate the water flow.

•  The exit-flow tube must allow free water discharge. We recommend that the water pressure inside the 

machine, does not exceed the 1.0 - 1.5 bar.

•  To connect the external parts, use a flexible tube with an inside diameter of 13 mm, safely fixed by a metal 

band with a screw that can be closed with a screw-driver or key (Figure 5).

CONTROL OF THE INSTALLATION

N.B.: Every operation is voluntarily commanded by means of the start button with the tank safety lid 

closed by means of the double safety device.

Turn the selector to the knead position  

  (Figure 6A) and check:

•  Make sure that the mixer is rotating counter- clockwise, facing the front of the machine, when the switch 

(Figure 6A) is placed on the “mix” position  

 , (the Archimedean screw also turns counter-clockwise). In 

the “0” position all of the machine’s elements should be still; in the drawplate position   , the mixer turns 

clockwise, the Archimedean screw should turn the same way (check from the lid slits).

Summary of Contents for PM-IT-0008





































Reviews: