background image

13

Troubleshooting

PROBLEMS, CAUSES AND SOLUTIONS

The processor has been designed to need minimum maintenance, however, some performance failures may 

happen due mainly to natural worn out, caused by the use of the processor. If some problems arise with your 

processor check table below where there are detailed some possible solutions.

PROBLEMS

CAUSES

SOLUTIONS

The machine does not start.

Open disc chamber lid.

Close the lid.

Problems with electric circuits.

Call technical assistance.

Electric energy shortage.

Check electricity supply.

The plug is out of socket.

Place the plug in.

Smoke or burn smell.

Problems with electric circuits.

Call technical assistance.

Irregular cuts.

Blunt knifes.

Sharpen the knife.

The processed product remains 

inside the machine.

Expeller dish is missing.

Place the expeller dish.

The machine switches ON, but 

when the product is inside the 

machine stops or runs slowly.

Belt is slipping.

Stretch the belt.

Electric shortage.

Check electricity supply.

Chamber lid safety system has bad 

contact.

Call technical assistance.

Unusual noises.

Problem with the bearings.

Call technical assistance.

Maintenance

salts, iodine compounds, nitric acid and others), must be AVOIDED, once it cannot remain for long in contact 

with the stainless steel.

These substances attack the stainless steel due to the CHLORINE on its composition, causing corrosion spots 

(pitting). Even detergents used in domestic cleaning must not remain in contact with the stainless steel longer 

than the necessary, being mandatory to remove it with plain water and then dry the surface completely.

USE OF ABRASIVES:

Sponges or steel wool and carbon steel brushes, besides scratching the surface and compromising the 

stainless steel protection, leave particles that rust and react contaminating the stainless steel. That is why such 

products must not be used for cleaning and sanitization. Scrapings made with sharp instruments or similar 

must also be avoided.

MAIN SUBSTANCES THAT CAUSE STAINLESS STEEL CORROSION:

Dust, grease, acid solutions such as vinegar, fruit juices, etc., salty solutions (brine), blood, detergents (except 

for the neutral ones), common steel particles, residue of sponges or common steel wool, and also other 

abrasives.

Summary of Contents for 44532

























Reviews: