manualshive.com logo in svg

OMB EM 100 DIG, Technical Manual, Page: 37 / 61

Share
Download
OMB EM 100 DIG Technical Manual Download Page 37

FM Transmitter 

Sistemas Electrónicos S.A                                                                                                                       EM 100 DIG

 Technical Manual - v1.2 -  November 2005

        33

3.1 Introduction. 

The EM-100 DIG transmitter comprises 5 or 6 internal modules. Main units are the following: 

™

 Main Board. 

™

 Microcontroller Unit & Display Board. 

™

 Stereo Coder Module (optional) 

™

 RF Exciter  Board. 

™

 RF Power Amplifier Module. 

™

 Switching Regulated Power Supply  

For the detailed description of some of these modules on the following pages, always refer to the 
corresponding electrical diagram. 

THIS SECTION IS ONLY AIMED TO GENERAL EXPLANATION,REFERENCE AND SERVICE PURPOSE BY SKILLED 
PERSONNEL. AS EXPLAINED IN THE PREVIOUS SECTIONS, INTERNAL ADJUSTMENTS ARE NOT REQUIRED 

DURING NORMAL OPERATION. TAMPERING WITH INTERNAL SETTINGS VOIDS THE WARRANTY, MAY HARM 
THE APPARATUS AND JEOPARDIZE THE GUARANTEED PERFORMANCE. 

                     COMPONENT VALUES SHOWN MAY VARY FOR PRODUCTION REQUIREMENTS. 

DUE TO THE TECHNOLOGY USED, MOST MODULES AND ESPECIALLY THOSE IN SMT ARE NOT INTENDED TO 
BE REPAIRED IN CASE OF FAILURE AND MUST BE REPLACED WITH NEW ONES.  

3.2 Main board.

This is the most complex board in the transmitter and supports the Audio input processing, its level 
adjustment, audio-pass filtering and limiting, the RF control section and the I/O interfaces. It also 

interconnects the various transmitter modules with ribbon-type cables. Its electrical diagram is splitted 
in two sheets for clarity purpose: they will be examined in sequence. In the first Schematics sheet are 
situated the I/O interfaces both audio and digital ports and the analog RF control. Let's start to briefly 
consider each block diagram. 

In the upper left side of the diagram are located the audio channels amplifier/buffers made with 6 
op-amp sections of IC1 and IC2.Two impedance selector jumpers for the audio channels leads the 
pack and a protection network made by resistors and diodes protects the inputs from occasional 
static discharges,as required for CE compliance. 

Four unity-gain active buffers follow and than two balanced to unbalanced signal converters,which 
drive the electronic attenuator in the 2

nd

 sheet. The last op-amp in IC2 (d),amplify the auxiliary 

channel input with a -0.1dB  upper corner band >>200kHz and drives the third channel of the 
electronic attenuator.

On the lower left of the diagram are the RS232 interface (IC5)and the parallel remote I/O active 
interface with its protection network, built around TR1, TR2 and TR3. A wired OR pull-up makes the 
logic levels <1V as 0 and 10~15V for 1. 

Summary of Contents for EM 100 DIG






























































Reviews:

No comments