manualshive.com logo in svg

OMB EM 100 DIG, Technical Manual, Page: 33 / 61

Share
Download
OMB EM 100 DIG Technical Manual Download Page 33

FM Transmitter 

Sistemas Electrónicos S.A                                                                                                                       EM 100 DIG

 Technical Manual - v1.2 -  November 2005

        29

This screen in command mode, with the 2

nd

 level password authorization, permits to set LF input 

channels sensitivity, i.e.multiplex, left and  right channel. Take  present  that multiplex and left signals 

share the same channel and the sensitivity is set to the same value for both left (or multiplex)and right 
channel,with a differential error <0.2dB at any level. Allowed range is -3.5 ~ +12.5dBm. 

The first line of the display shows the actual modulation,while the bottom line shows the input level for 

100% modulation.Increasing the input level will accordingly decrease the modulation. 

M

ENU

#23:P

ASSWORD

C

ONFIRMATION

conf. password 

* * * * 

This screen is displayed when password code or mode is changed on menu # 13. It requires entering 
the same password code as in the current level which is to be changed. Failure to do so will show the 
message:ERROR PASSWORD. 

This display stops input mode for 5 second and than permits to exit (and possibly to try again) with the 
<CANCEL> key. 

M

ENU

# 25: A

UXILIARY

C

HANNEL

I

NPUT

L

EVEL

S

ET

.

set aux. gain 

This screen in command mode, with the 2nd level password authorization, permits to set the auxiliary 
channels input sensitivity. Allowed range is -12 ~ +4 dBm to produce 10%modulation, i.e. 7.5kHz  
deviation  or 0dB in the upper line of the display. 

M

ENU

#27:O

PERATION

M

ODE

,P

REEMPHASIS AND 

F

REQUENCY

S

ET

set mode, preenf. 

& freq.

In  this  screen  it  is  possible  to  set  the transmission "modes" (MONO R, STEREO, MONO L+R, EXT 
MPX), the preemphasis time constant (0, 25, 50 & 75µs) and the frequency in step of 10 or 100kHz as 
preset on the menu # 37. To access to this last menu, the 3

rd

 authorization level is required, from the 

main frequency menu # 07. 

Left and right keys change the input fields whilst the up and down keys change the various options or 
increase/decrease the frequency. 

Summary of Contents for EM 100 DIG






























































Reviews:

No comments