manualshive.com logo in svg

OMB EM 100 DIG, Technical Manual, Page: 32 / 61

Share
Download
OMB EM 100 DIG Technical Manual Download Page 32

FM Transmitter 

Sistemas Electrónicos S.A                                                                                                                       EM 100 DIG

 Technical Manual - v1.2 -  November 2005

        28

If the code or the status is changed, it is always required to confirm the correct password for that 
level. If the password is unknown, lost or tamperers changed it, it is possible to change status and 

code when in possession of the higher password. In this case the lower level password code must be 
changed and confirmed: no possibility still being to know what was the old password.  

In case a lower password permission is actually set in regard to the needed action, it is possible to 

input the higher level password either performing a software reset, if permitted, or turning off and on 
the mains voltage through the rear mains switch or an external switch. 

The 3

rd

 level authorization, when set, will stay valid only till a display time-out is performed,i.e.usually 3 

minutes after the last command. Simply navigating through the menu or performing some action will 

prolong the time-out. 

If the password status is set to on for the level 1, a hung-up may follow after the time-out.This may be 
intentional to prevent unauthorized people from browsing the exciter parameters. Exciter 
performance will be unaffected by this condition. Any attempt to access the exciter will cause the 

password request:if an invalid password in entered,it needs to wait for the time-out to permit a new 
attempt or to remove the mains power to the equipment,causing a hardware reset. Even in this 
case, the first request will be a valid password input. 

M

ENU

# 14: S

OFTWARE

R

ESET

exec. sw reset ? 

yes/no 

This screen permits to execute a software reset if in possession at least of level 1 password 
authorization. The main purpose of this reset is permitting to input a new password level; its action is 

similar to turning off and on the mains to the equipment. A software reset will lead to a small 
interruption of the RF output power which will be re-established in few seconds, while lock on 
frequency will not be lost.No transmission or sensitivity parameter is lost in consequence of software or 
hardware reset. 

M

ENU

# 21:O

UTPUT

P

OWER 

S

ET

.

set dir power 

This screen derives from #01, in command mode. The direct power value blinks and acting on up 
and down keys the numeric value varies. The output power will vary in real time.Confirming the final 
value with an "OK" will write the new setting in the non-volatile memory of the equipment. Escaping  
(<CANCEL>) will abort the change. 

A local time-out  will automatically escape the input if not confirmed in 30 seconds from the last 
change performed. 

M

ENU

# 22:M

ULTIPLEX

, L

EFT

& R

IGHT

I

NPUT

L

EVEL

S

ET

.

set mpx gain 

Summary of Contents for EM 100 DIG






























































Reviews:

No comments