manualshive.com logo in svg

OMB EM 100 DIG, Technical Manual, Page: 29 / 61

Share
Download
OMB EM 100 DIG Technical Manual Download Page 29

FM Transmitter 

Sistemas Electrónicos S.A                                                                                                                       EM 100 DIG

 Technical Manual - v1.2 -  November 2005

        25

M

ENU

#00:D

EFAULT

M

ESSAGE

.

OMB EM-100 DIG 

VER 1.0

This screen shows the default message and the software release.It is the field that will be initially set, or 
to which it will return back after repeated CANCEL commands. 

If authorized by the 3rd level permission, going in the command mode (inputting <OK>) will permit 

to edit the first row of this field with a custom message e.g.your organization name. 

M

ENU

# 01:D

IRECT

& R

EFLECTED

P

OWER

.

dir. power ;   100 W 

REF. POWER:    0.0 W

This screen shows the direct and reflected power actually delivered.Going in the command mode, 
with the 2nd level password authorization, will permit to set a new direct RF output power. See menu 
# 21. 

M

ENU

# 02:M

ULTIPLEX

S

IGNAL

L

EVEL

(O

UTPUT

M

ODULATION

)

MPX     75KHz  +7.1 DB 

ŰŰŰŰŰŰŰŰŰŰŰŰ

This screen shows the actual peak modulation in dB referred to 75kHz and as deviation in kHz. A 
pseudo-analog moving bar simultaneously fast changes with the modulation, leaving a peak mark 
at its end for 1 or 2 seconds. A vertical bar ( | )  on this line marks the  0dB position. 

Command mode, with the 2

nd

 level password authorization, permits to set LF input channel sensitivity, 

or modulation depth. See Menu # 22. 

Right key,with the 3rd level password authorization,permits to access to limiter setup and 
threshold.See Menu # 32. 

M

ENU

# 03:L

EFT

& R

IGHT

S

IGNAL 

L

EVEL IN D

B

LEFT level -3.0 db 

right level -4.0 db

This screen shows the actual left and right peak modulation in dB referred to 75kHz.The reading is 

adequately accurate with real audio signals. Some steady state test tone especially at very low 
audio frequency may beat with the discrete A/D conversion sometimes producing some reading 

Summary of Contents for EM 100 DIG






























































Reviews:

No comments