Olympus VISERA ENF-V2 Instructions Manual Download Page 56

52

Chapter 7  Cleaning, Disinfection and Sterilization Procedures for Endoscopic Instruments

VISERA RHINO-LARYNGO VIDEOSCOPE ENF-V2

• Do not store disinfected instruments. Use them immediately 

after disinfection or forward them to the following sterilization 
process. If stored instruments are used, refer to your local 
regulations and/or guidelines.

• Do not immerse instruments for more than 60 minutes in any 

liquids. If instruments are left immersed in liquids for a longer 
period, too much humidity inside of the endoscope will arise, 
which will cause malfunction.

When the regulation/guideline in your region requires 
disinfection prior to sterilization for the personnel in charge of 
reprocessing, perform the sterilization after the procedure of 
Section 6.6, “Automatic cleaning/disinfection” on page 41 or 
Section 7.7, “Disinfection” on page 63.

7.3

Precleaning

Preclean the endoscope immediately after the procedure. The following steps 
are to be performed when the light source and the video system center are 
turned OFF.

Endoscopic instrumentation must be meticulously cleaned 
prior to disinfection or sterilization. Thorough cleaning 
removes both micro-organisms and organic material. Failure 
to remove organic material decreases effectiveness of the 
disinfection or sterilization procedure. If the endoscope is not 
immediately precleaned, residual organic debris will dry on 
the instrument and effectively reprocessing will be difficult.

Equipment needed

Prepare the following equipment and wear appropriate personal protective 
equipment.

• Personal protective equipment
• Clean, lint-free cloth
• Detergent solution
• 500 cm

3

 (500 ml) containers

• De-ionized water (Aq. Dest.)

Summary of Contents for VISERA ENF-V2



























































































Reviews: