background image

OLYMPUS Industrial Web Printer Operation Guide Rev.001                        11/19 

 

1.1. WARNING   

 

 

1.1.1. General 

1)  Prohibit any person to operate the unit except for designated operator given proper training.

 

Wrong 

operation may cause unexpected accident. 

 

2)  Prohibit any person with a pacemaker to get close to the unit. 

3)  Do not insert a hand to the unit during operation. It may cause the serious injury if a part of sleeve or 

finger tip is caught by roller.   

4)  Be careful of any loose part getting caught and pulled into the unit.

 

(I.e. tie, sleeve, hair, and strap)   

5)  Main power of the 

Main Power Unit

 must be down while on service.

 

There is a danger of electric struck 

or injury. 

   

1.1.2. 

Machine 

Setting 

   

 

1)  The main unit must be fixed position by four levelers on each corner after set on the proper position.   

2)  Locate the unit with enough space on surrounding area. 

3)  Stop using the machine and contact Olympus immediately if any miss-operation observed on a device 

located near by.   

4)  Stop using the machine, turn off the power of the 

Main Power Unit

, and contact Olympus immediately 

when ink leakages occur. 

5)  Not for use in a computer room as defined in the Standard for the Protection of Information Technology 

Equipment. ANSI/NFPA 75. 

 

1.1.3. Unwinder 

(Warning) 

 

 

 

1)  Do not load the paper weight exceeding 300kg (660lbs). Otherwise there is a danger of the machine 

falling down and damage.   

2)  Do not print while bottom of paper roll is in contact with the ground. Otherwise, there is a concern of paper 

cut off and the machine damage. 

3)  Must stay within the location where 

Emergency Stop Button

 can be reached while replacing the roll 

paper. 

4)  Do not stand behind the roll paper while replacing. There is a danger of injury when paper roll down. 

5)  Do not place feet under the roll paper. There is a danger of injury when paper falls off. 

 

1.1.4. Unwinder 

(Caution) 

 

1)  Do not completely remove the paper from the machine. Connect leading edge of the new paper to the 

remaining old paper when replacing. 

2)  The print head must move up from the printing position by selecting the 

Paper Replace Mode

 change on 

CAUTION 

WARNING 

WARNING 

CAUTION 

Summary of Contents for OP1 SERIES




















Reviews: