background image

20

9

Objective

Type

MPLN

Eyepiece

Working distance: Distance between the surface of a specimen and the tip of the objective.

Aperture number: Essential value to determine the characteristics (resolution, depth of focus and brightness) of an

objective:
Resolution .......................................
Depth of focus ...........................
Brightness .......................................

Increases relative to the aperture number.
Decreases relative to the aperture number.
Changes in proportion with the square of the aperture number (the same
magnification comparison).

Resolution:

Represented by the interval between two points on a specimen which determine the ability of an
objective to distinguish two images close to each other.

Depth of focus:

The degree to which the portions of the image from front to back can be seen in focus simulta-
neously. The lower the aperture iris diaphragm, the greater the depth. The higher the aperture number,
the shallower the depth.

Field number:

The diameter of the area viewed through an eyepiece represented in millimeters.

OPTICAL CHARACTERISTICS

Magnification

5X

10X

20X

50X

100X

Numerical aperture

0.10

0.25

0.40

0.75

0.90

Working distance (mm)

20.0

10.6

1.3

0.38

0.21

Resolution (μm)

3.36

1.34

0.84

0.45

0.37

WHB10X
(Field number 20)

Total magnification

50X

100X

200X

500X

1000X

Depth of focus (μm)

98

18

6.1

1.4

0.73

Field of view (mm)

4

2

1

0.4

0.2

WHN10X
(Field number 22)

Total magnification

50X

100X

200X

500X

1000X

Depth of focus (μm)

98

18

6.1

1.4

0.73

Field of view (mm)

4.4

2.2

1.1

0.44

0.22

The table below shows the optical characteristics of
different eyepiece and objective combinations. Ob-
jective specifications are marked on the objective (as
shown in the diagram on the right).

NOTE

Refer to the latest catalogue or consult Olympus for
the updated information on the eyepieces and objec-
tives that can be combined with this unit.

Magnification

UIS marking

Cover glass thickness

—: May be used with our with-

out a cover glass.

0: Used without a cover glass.

-- The UIS series objectives that are not mentioned below can also be mounted on this microscope. --

FN (Field Number)

Objective series

(PL = Plan)

NA (Numerical of Aperture)

Field of view:

The diameter of the area observable on the specimen, expressed in mm.

Summary of Contents for GX41

































Reviews: