manualshive.com logo in svg

OLT SM812-FJ-Ply, Assembly Manual, Page: 35 / 43

Share
Download
OLT SM812-FJ-Ply Assembly Manual Download Page 35

Square Cut Facia

Angled Facia

Angled Facia caps 
Square Cut Facia.

63.

  Position 

Rear Facia 

(angle cut on ends) and 

Side Facia

 

(square cut ends) in corner.  Line Facia up so angle cut Facia 
caps square cut Facia.  Attach angled Facia to Nailing Strip with 

8 - 1 1/2” Finishing Nails

 per piece.  Gap where facia boards 

come together at peak will be covered in 

Step 65.  

Do a dry run 

using Side Facia to help you correctly position before attaching.

Parts (Steps 63 - 64)

 

Front & Rear Facia 

- Angle Cut Ends

 

(3/4” x 3 1/2” x 58”) 

x 4 

Side Facia 

(3/4” x 3 1/2” x 71 3/4”) 

x 4

Hardware (Steps 63 - 64) 

N1

 

- 1 1/2” Finishing Nails

 x 64 total

Hardware 

S2

 

- 1 1/4” Screws

 x 12 total

61.

  Attach 

Horizontal Door Trim

 onto the exposed part of 

the Door Header, and tight under the lip of the Drip Cap. 
Secure Horizontal Door Trim with 

5 - 1 1/2” Finishing Nails

.

Parts

 

Horizontal Door Trim 

(1/2” x 1 1/2” x 64”) 

x 1 

Hardware 

N1

 

- 1 1/2”  

Finishing Nails

 x 5 

total

62.

  Attach

 Facia Nailing Strips 

to the underside edge of 

the plywood roof. Align corner of Nailing Strip with edge of 
roof plywood. Secure each Strip with 

3 - 1 1/4” Screws

.  

Complete all four pieces, two on each side of the shed.

Parts

 

Facia Nailing Strips 

(3/4” x 2 1/2” x 51”) 

x 4

  Toll Free 1-888-658-1658              www.outdoorlivingtoday.com        [email protected]

Page 35

Summary of Contents for SM812-FJ-Ply












































Reviews:

No comments