manualshive.com logo in svg

OLT SM812-FJ-Ply, Assembly Manual, Page: 24 / 43

Share
Download
OLT SM812-FJ-Ply Assembly Manual Download Page 24

38. 

 

Rafter Nailing Cleat

 are positioned on the center rafter. Have a helper 

lineup 

Rafter Nailing Cleat

 along the center rafter. Top of  

Rafter Nailing Cleat

 

should be flush with top of the rafter to support plywood roof. Position 

Rafter 

Nailing Cleat

 to be 4 1/4” from each end of rafter as shown below. Pre-drill pilot 

holes in the 

Rafter Nailing Cleat

 and then attach to rafter with 

3 - 1 1/4” 

screws

. Repeat for each side of the rafter and then on opposite side of the roof

Parts

 

Rafter Nailing Cleat 

(3/4” x 1 1/2” x 48”) 

x 4

Hardware  

S2

 

- 1 1/4” Screws

 

x 12 total

Lineup 

Rafter Nailing Cleat

 approximately  

4 1/4” from end of rafter near soffit.

Lineup 

Rafter Nailing Cleat

 approximately  

4 1/4” from end of rafter near ridge board.

4 1/4”

4 1/4”

Important: 

On each 

Rafter Nailing Cleat 

pre-drill three 

pilot holes on the side of the cleat before attaching to cen-
ter rafter to prevent splitting of nailing cleat.

  Toll Free 1-888-658-1658              www.outdoorlivingtoday.com        [email protected]

Page 24

Summary of Contents for SM812-FJ-Ply












































Reviews:

No comments