manualshive.com logo in svg

OLT SM812-FJ-Ply, Assembly Manual, Page: 26 / 43

Share
Download
OLT SM812-FJ-Ply Assembly Manual Download Page 26

Small plywood roof panels (2/side)  
5/8” x 8 1/2” x 72”

Exploded view of upside down roof panels.

Large Roof Panel.

42. 

 Identify all Roof Panels. There are 4 Large and 

4 Small Roof Panels.  2 of each sized panel are used 
per side. Locate one large sheet of Roof Plywood . 
Position on right side of shed. Recess plywood back 
approximately 1/8” from end of rafter.

Parts (Steps 42 - 48)

 

Large Roof Panels 

(5/8” x 48” x 72”) 

x 4 

Small Roof Panels 

(

5/8” x 8 5/8” x 72”

 ) 

x 4

Hardware (Steps 42 - 48) 

S2

 

- 1 1/4” Screws

 

x 84 total

Large plywood roof panels (2/side) 
5/8” x 48” x 72”

    

4”

Back approx. 1/8”

Plywood centered 
on 5th rafter.

43. 

 Plywood will overhang the front rafter by 4”. On opposite side, plywood will be centered 5th 

rafter still being supported by second rafter nailing cleat.

44. 

 With Roof Plywood correctly positioned on rafters, attach with 

12 - 1 1/4”

 screws. 

On 5th rafter,   be sure to angle screw to hit the meat of the rafter.

  Toll Free 1-888-658-1658              www.outdoorlivingtoday.com        [email protected]

Page 26

Summary of Contents for SM812-FJ-Ply












































Reviews:

No comments