manualshive.com logo in svg

OLT SM812-FJ-Ply, Assembly Manual, Page: 23 / 43

Share
Download
OLT SM812-FJ-Ply Assembly Manual Download Page 23

Gable Notch

Ridge Board

91” Across

Offsetting Metal Ridge 
Board Connectors.

37.

 With both Ridge Boards connected, 

completely secure Gable framing to 
walls and rafters.  Use 

4 - 2” Screws

 per 

Rafter.  Use an additional 

6 - 2” Screws

 

to secure Gable to wall.

 

Note: you may have to remove the  
2 temporary screws in Gable from 
Step 27 and reposition Gable for best 
fit prior to completing Gable  
attachment.

Hardware 

S3

 

- 2” Screws

 x 28 total

35.

  Place second completed Rafter Section 

on gable walls as per 

Steps 32 - 34.

36.

  At the peak, align Ridge Boards so 

they are flush together and secure them with 

12 - 1 1/4” Screws

. 

Important:

  If there is a gap between Ridge 

Boards, have a helper push the Side Walls 
closer together from outside.  Walls should 
be 91” apart at top from inside of wall plate 
to opposite wall plate.  To completely secure 
Ridge Boards, place

 1 1/4” Screws

 into any 

of the remaining metal Ridge Board 
Connector holes. Complete both sides.

Hardware 

S2

 

- 1 1/4” Screws

 x 20 total (approx.)

  Toll Free 1-888-658-1658              www.outdoorlivingtoday.com        [email protected]

Page 23

Summary of Contents for SM812-FJ-Ply












































Reviews:

No comments