OLT GS63-TG-METAL Assembly Manual Download

Page: 25 / 33

Outdoor Living Today www.outdoorlivingtoday.com [email protected]

Page 25

44.

Locate a

Rear Side Corner Trim

and

Rear Wide Corner Trim.

Once again, angled Side Trim

pieces are unique to each corner and are attached

rough side out

. Position Rear Side Trim tight

underneath Side Fascia Trim. Align Rear Wide Corner Trim underneath Metal Roof and flush with
Side Fascia Trim. Rear Side Corner Trim will cap Rear Wide Corner Trim. Attach each piece with

6 - 1 1/2” Finishing Nails.

Rear Wide Corner Trim

Rear Side
Corner Trim.
Angle Cut 8
Deg. At Top.

45.

Locate

Upper Rear Horizontal Trim

and align tight against Rear Wide Corner Trim and

underneath Metal Roof. Attach to Rear Filler Strip with

6 - 1 1/2” Finishing Nails.

Parts

Rear Wide Corner Trim

(1/2” x 3 1/2” x 67 3/4”)

Rear Side Corner Trim (Angle Cut At Top)

(1/2” x 2 1/2” x 65 1/2”)

Hardware

1 1/2” Finishing Nails

x 12 total

Tight

Side Fascia

Trim

Rear Side Corner Trim will cap
Rear Wide Corner Trim.

Flush

Parts

Upper Rear Horizontal Trim

(1/2” x 2 1/2” x 67 1/4”)

Hardware

1 1/2” Finishing Nails

x 6 total

Locate

Rear Center Trim.

Align tight

against Upper Rear Horizontal Trim and attach
with

6 - 1 1/2” Finishing Nails.

Parts

Rear Center Trim

(1/2” x 2 1/2” x 65 1/8”)

Hardware

1 1/2” Finishing Nails

x 6 total

Rear Center Trim

Tight Underneath
Upper Rear
Horizontal Trim

Summary of Contents for GS63-TG-METAL


































Search results

Summary of Contents for GS63-TG-METAL

Reviews:

Related manuals for GS63-TG-METAL

Brands by name

Popular brands

OLT GS63-TG-METAL, Assembly Manual

Search results

Summary of Contents for GS63-TG-METAL

Reviews:

Related manuals for GS63-TG-METAL

Brands by name

Popular brands