OLT GS63-TG-METAL Assembly Manual Download

Page: 29 / 33

Outdoor Living Today www.outdoorlivingtoday.com [email protected]

Page 29

56.

Attach

Black Drop Latch

as illustrated above with

6 - 3/4” Black Headed Screws.

Note:

Black Drop Latch receiver is positioned higher than male. Do a dry run first to position Black

Drop Latch correctly.

Important

- Drill pilot holes with 1/8” drill bit prior to securing with screws to

prevent wood splitting.

Important: Drill shallow Pilot
Holes to prevent splitting.

Drop Latch
Receiver

3/4” Black Screw

57.

Install the

Plywood Spacer

to interior door

frame approximately 1 1/2” from top of door frame
and 1” from edge, as pictured. Use

2 - 1 1/4”

Brown Screws

to secure. Plywood Spacer

should fit flush underneath Interior Door Header
when Door is closed.

Mark Door
Stop

58.

Position the

Interior Silver Barrel Bolt

on the Plywood Spacer and attach with

4 - 3/4” Silver

Screws.

Tap Silver Barrel Bolt with hammer on underside of Interior Door Header to mark location.

Hardware

Interior Silver Barrel Bolt

3/4” Silver Screws

x 4 total

Hardware

Plywood Spacer (

1/2” x 2 1/2” x 2 1/2”)

1 1/4” Brown Screws

x 2 total

Silver Barrel Bolt

Hardware

Black Drop Latch

3/4” Black Headed Screw

x 6 total

3/4” Black
Screws

3/4” Black Screws

Summary of Contents for GS63-TG-METAL


































Search results

Summary of Contents for GS63-TG-METAL

Reviews:

Related manuals for GS63-TG-METAL

Brands by name

Popular brands

OLT GS63-TG-METAL, Assembly Manual

Search results

Summary of Contents for GS63-TG-METAL

Reviews:

Related manuals for GS63-TG-METAL

Brands by name

Popular brands