OLT GS63-TG-METAL Assembly Manual Download Page 26

Page: 26 / 33

Outdoor Living Today www.outdoorlivingtoday.com [email protected]

Page 26

48.

Locate 2

Vertical Door Frame Trims.

Position on Front Narrow Wall flush with Wall siding/

framing and underneath Front Header Filler Strip. Attach with

6 - 1 1/2” Finishing Nails.

Flush with Siding/
Wall Framing

Parts

Vertical Door Frame Trims

(1/2” x 2 1/2” x 64 1/4”)

x 2

Hardware

1 1/2” Finishing Nails

x 12 total

49.

Locate

Door Threshold

and position on Floor at the opening. Align tip of the bevel flush with

the outside of the Bottom Wall Plate. Attach with

4 - 1 1/4” Brown Screws.

Butt

Tip

2 5/8”

Flush

Parts

Door Threshold (Bevel)

(1/2” x 2 5/8” x 44 7/8”)

Hardware

1 1/4” Brown Screws

x 4 total

47.

Complete other Rear Corner, Side Fascia

and Front Corner Trims as per

Steps 42 - 44.

Parts

Rear Wide Corner Trim

(1/2” x 3 1/2” x 67 3/4”)

Rear Side Corner Trim (Angle Cut At Top)

(1/2” x 2 1/2” x 65 1/2”)

Side Fascia Trim (Angle Cut Both Ends)

(1/2” x 2 1/2” x 37 5/8”)

Front Wide Corner Trim

(1/2” x 3 1/2” x 70 3/8”)

Front Side Corner Trim (Angle Cut At Top)

(1/2” x 2 1/2” x 70 3/8”)

Hardware

1 1/2” Finishing Nails

x 28 total

Summary of Contents for GS63-TG-METAL


































Search results

Summary of Contents for GS63-TG-METAL

Reviews:

Related manuals for GS63-TG-METAL

Brands by name

Popular brands

OLT GS63-TG-METAL, Assembly Manual

Search results

Summary of Contents for GS63-TG-METAL

Reviews:

Related manuals for GS63-TG-METAL

Brands by name

Popular brands