OLT GS63-TG-METAL Assembly Manual Download Page 24 | Manualshive

Page: 24 / 33

background image

Outdoor Living Today www.outdoorlivingtoday.com [email protected]

Page 24

42.

Locate a

Front Wide Corner Trim

and

Front Side Corner Trim.

Angled Side Trim pieces are

unique to each corner and are attached

rough side out

. Starting in one corner, position both Trims

up tight underneath Upper Front Horizontal Trim. Align Front Wide Corner Trim flush against Upper
Front Horizontal Trim. Front Side Corner Trim will cap Front Wide Corner Trim. When correctly
aligned, attach each piece with

6 - 1 1/2” Finishing Nails.

Upper Front Horizontal

Trim

Tight

Expert Advice:

Do a dry run with Front and Rear Corner Trims before
attaching. Confirm the rough face is configured correctly and
small trim gaps are satisfactory before attaching.

43.

Continuing around the shed, place a

Side Fascia Trim

tight against Upper Front Horizontal

Trim and underneath Metal Roof. Align Side Fascia with Side Corner Trim. Attach Side Fascia Trim
to Side Angle Gable with

4 - 1 1/2” Finishing Nails.

Tight

Upper Front Hor

.Trim

Side Fascia

Parts

Side Fascia Trim (Angle Cut Both Ends)

(1/2” x 2 1/2” x 37 5/8”)

Hardware

1 1/2” Finishing Nails

x 4 total

Parts

Front Wide Corner Trim

(1/2” x 3 1/2” x 70 3/8”)

Front Side Corner Trim (Angle Cut At Top)

(1/2” x 2 1/2” x 70 3/8”)

Hardware

1 1/2” Finishing Nails

x 12 total

Front Side Corner Trim 2 1/2”
Wide. Angle Cut 8 Deg. at Top.

Front Wide Corner
Trim 3 1/2” wide.
Flush with Upper
Front Horizontal Trim.

«
...
22
23
24
25
26
...
»

Summary of Contents for GS63-TG-METAL


































Reviews:

No comments

Related manuals for GS63-TG-METAL

Palmako Grete ELU16-2317

Brand: Lemeks Pages: 84

Brand: Mercia Garden Products Pages: 7

Brand: Palmako Pages: 37

Annabel EL18-4533-4

Brand: Palmako Pages: 45

Brand: Palmako Pages: 28

Brand: Solid Build Pages: 10

Brand: Yardistry Pages: 32

OAKRIDGE 8 x 12

Brand: Yardline Pages: 88

STOCKTON 8' x 12'

Brand: Yardline Pages: 56

Brand: Karibu Pages: 57

Brand: Palmako Pages: 104

Brand: Feider Machines Pages: 22

Brand: Solid Pages: 16

Brand: Tiger Pages: 24

TIGERFLEX Copia

Brand: Tiger Pages: 32

Brand: Prestige Garden Pages: 18

Brand: Alfer Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands