background image

Toll Free 1-888-658-1658           www.outdoorlivingtoday.com            [email protected]

8x8 Sunshed Garden Shed  

FJ Bevel Model with Metal Roof  

Assembly Manual

Page 1

Revision #2.1 
April 22, 2021

Some of the safety and usage measures you may wish to consider include: 
 
-snow load ratings vary by geographical location. If heavy or wet snowfall occurs, it is advisable to sweep the 
snow off the roof(s).  
-if the product is elevated, any structural and building code requirements are solely the customer's  
responsibility, and should be abided by.  
-in high or gusty wind conditions it is advisable to keep the structure securely grounded.  
-have a regular maintenance plan to ensure screws, doors, windows and parts are tight. 

In the event of a missing or broken piece, simply call the Outdoor Living Today Customer 
Support Line @ 1-888-658-1658 within 30 days of the delivery of your purchase. It is our  
commitment to you to courier replacement parts, free of charge, within 10 business days of 
this notification. Replacement parts will not be provided free of charge after the 30 day grace 
period. 

Reversible 
Roof Lines

Thank you for purchasing 
an 8x8 SunShed Garden 
Shed from Outdoor Living  
Today. Please take the 
time to identify all the 
parts prior to assembly.

Customer agrees to hold Outdoor Living Today Partnership and any Authorized Dealers free of 
any liability for improper installation, maintenance and repair.

Safety Points and Other Considerations 
Our products are built for use based on 
proper installation and normal residential 
use, on level ground. Please follow the  
instruction manual when building your  
shed and retain the manual for future  
maintenance purposes.

Stock Code # 
SSGS88-FJ-Metal

Summary of Contents for FJ Bevel






































Reviews: