OLT GS124-SLIDER-CEDAR-AK Assembly Manual Download Page 39

Page: 39 / 42

63.

Attach

4T - Front Facia - Center

to rafter ends as shown above. Small gaps may occur between the

Center and Left/Right Facia, but these will be covered by Facia Detail Plates in

Step 65

Attach with

2 - 1 1/2” Finishing Nails

per rafter end.

64.

Attach

4S & 4T - Rear Facia

onto rafter ends as per

Steps 61 - 63

. Small gaps may occur between

the Center and Left/Right Facia, these will be covered by Facia Detail Plates in

Step 65

. Rear Facia will

cap the side Facia. Attach Rear Facia to rafter ends with

2 - 1 1/2” Finishing Nails

per rafter end.

Small gaps may occur.

Side Facia

Rear Facia

Rear Facia caps
Side Facia.

Small gaps may occur.

62.

Attach other Front and Side Facia to opposite corner as per

Step 61

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 39

Summary of Contents for GS124-SLIDER-CEDAR-AK











































Search results

Summary of Contents for GS124-SLIDER-CEDAR-AK

Reviews:

Related manuals for GS124-SLIDER-CEDAR-AK

Brands by name

Popular brands

OLT GS124-SLIDER-CEDAR-AK, Assembly Manual

Search results

Summary of Contents for GS124-SLIDER-CEDAR-AK

Reviews:

Related manuals for GS124-SLIDER-CEDAR-AK

Brands by name

Popular brands