OLT GardenSaver GS124-SLIDER-METAL-FJ Assembly Manual Download | Manualshive

Page: 16 / 44

background image

20.

Place

2H - Extender Walls

on top of Door Header so that framing is

aligned with Angle Wall Extender framing in front as shown above.
With framing aligned, attach Extender Walls to Door Header and other
extenders with

4 - 2 1/2” Screws

each as shown below.

Parts

2H - Extender Walls

(2H - 45 1/2” wide)

x 3

Hardware

S1

- 2 1/2” Screws

x 12 total

19.

Complete opposite Angled Wall Extender positioning and attachment as per

Step 18.

Cleat protects overhanging
siding on upper walls from
damage. Please remove
before installing.

Overhanging
siding.

Protective
cleat

Siding overhang
rests in notch.

framing aligned
in front.

Framing flush
along top.

Pilot Hole

first.

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 16

«
...
14
15
16
17
18
...
»

Summary of Contents for GardenSaver GS124-SLIDER-METAL-FJ













































Reviews:

No comments

Related manuals for GardenSaver GS124-SLIDER-METAL-FJ

Brand: Palmako Pages: 44

Garden Chalet 4x2

Brand: OLT Pages: 18

GardenSaver GS84-SLIDER-PLY-AK

Brand: OLT Pages: 35

8x4 GardenSaver

Brand: OLT Pages: 38

Brand: OLT Pages: 39

Brand: STILLA Pages: 28

Brand: STILLA Pages: 24

Brand: STILLA Pages: 40

Brand: STILLA Pages: 48

Brand: STILLA Pages: 52

Brand: STILLA Pages: 56

The ORGANIC GARDEN AOGC15081HC

Brand: ABSCO SHEDS Pages: 25

Brand: ABSCO SHEDS Pages: 25

Brand: Palmako Pages: 128

Brand: Karibu Pages: 33

Brand: Palmako Pages: 51

Brand: Solid Pages: 16

Premier 30232GK-PTX

Brand: ABSCO SHEDS Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands